Component guide · Beginner · 5 min read
125kHz RFID

EM-18 and EM4100 Reader Modules, ID-12LA and ID-3LA, RD6300 UART Reader, WG26/34 IP65 Wiegand Reader, JT308 USB Reader, EM4305 and T5577 Rewritable Keyfobs, Coins and Cards, RW1990 and Silicone Wristbands
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
125kHz RFID is the low-cost proximity system used in office ID cards and keyfobs. Each EM4100-type tag carries a fixed ID that the reader sends as text over serial, Wiegand or USB keyboard. EM-18 and RD6300 modules connect to an Arduino serial pin. T5577 and EM4305 tags are rewritable, so a writer can copy an ID onto them. It is read-only ID, not secure storage.
Key specs at a glance
- Frequency
- 125kHz
- Tags
- EM4100/TK4100 read-only, T5577 and EM4305 rewritable
- Range
- 2 to 8cm typical
- Outputs
- UART 9600 (EM-18, RD6300, ID-12LA), Wiegand 26/34, USB HID keyboard
- Supply
- 5V modules, 12V Wiegand readers
- Forms
- Cards, keyfobs, coins, stickers, wristbands
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1EM-18 RFID Reader Module, 125 kHz₹280
Option 2EM4100 125kHz RFID Reader Module₹223
Option 3ID-Innovations ID-12LA RFID Reader Module – 125kHz, EM4001 Compatible₹4,539
Option 4ID-Innovations RFID Reader Module ID-3LA 125kHz Mini – Serial/Wiegand Output₹3,909
Option 5RD6300 RFID Card Reader Module – 125KHz EM4100, UART TTL RS232, 20-50mm Range₹155
Option 6WG26/34 125KHz RFID Contactless IP65 Smart Card Reader – ABS+PC Housing, Wiegand Output₹469
What the 125kHz RFID readers, EM4100 and T5577 tags and Wiegand readers is
125 kHz RFID is the older low-frequency proximity system: the reader powers a passive tag through a coil and the tag answers with its fixed ID number.
Use 125kHz for attendance, cupboard and door locks, pet doors and simple logins. USB readers (JT308) type the ID like a keyboard into any PC app. WG26 readers mount on a wall and output Wiegand to an access controller or an Arduino.
The tag ID can be copied, so do not use 125kHz alone for anything valuable. For secure systems use 13.56 MHz DESFire cards. Note that 125kHz readers cannot read MIFARE or NFC cards, and 13.56 MHz readers cannot read these tags.
125kHz RFID readers, EM4100 and T5577 tags and Wiegand readers pinout
The pins on the 125kHz RFID readers, EM4100 and T5577 tags and Wiegand readers and what each one does.
| Pin | Function |
|---|---|
| VCC | 5V |
| GND | Ground |
| TX / D0 | Serial data out (9600 8N1) |
| BEEP / LED | Read indicator on some boards |
| Antenna | Coil terminals on RD6300 and ID-3LA |
- VCC
- 5V
- GND
- Ground
- TX / D0
- Serial data out (9600 8N1)
- BEEP / LED
- Read indicator on some boards
- Antenna
- Coil terminals on RD6300 and ID-3LA
Wiring the 125kHz RFID readers, EM4100 and T5577 tags and Wiegand readers
Wiegand readers run on 12V but their D0/D1 lines are usually 5V open collector; check before connecting to 3.3V boards.
| 125kHz RFID readers, EM4100 and T5577 tags and Wiegand readers pin | Connection | Note |
|---|---|---|
| Module TX | D2 | SoftwareSerial RX |
| VCC | 5V | |
| GND | GND | Common |
| Wiegand D0 / D1 | D2 / D3 | WG26 reader, 12V supply, common GND |
- Module TX
- Connection:
- D2
- Note:
- SoftwareSerial RX
- VCC
- Connection:
- 5V
- GND
- Connection:
- GND
- Note:
- Common
- Wiegand D0 / D1
- Connection:
- D2 / D3
- Note:
- WG26 reader, 12V supply, common GND
Example code
EM-18 sends 12 ASCII characters; RD6300 wraps them in 0x02 and 0x03 bytes, which the isPrintable filter drops.
#include <SoftwareSerial.h>
SoftwareSerial rfid(2, 3); // RX on D2
void setup() {
Serial.begin(9600);
rfid.begin(9600);
Serial.println("Show a tag");
}
void loop() {
if (rfid.available()) {
String id = "";
unsigned long t = millis();
while (millis() - t < 50) {
if (rfid.available()) {
char c = rfid.read();
if (isPrintable(c)) id += c;
t = millis();
}
}
Serial.println("Tag: " + id);
}
}Setup and tuning
UART readers (EM-18, RD6300, ID-12LA) plug into an Arduino serial pin; Wiegand readers suit access-control panels; USB readers type the ID like a keyboard.
most UART readers send 9600 baud, 8N1. Use SoftwareSerial on an Uno so the USB port stays free for the monitor.
keep the coil away from metal plates and motors. Metal behind the coil can cut the range to almost nothing.
a tag held at the reader repeats its ID many times; ignore the same ID for one or two seconds.
Wiegand readers need 12 V, and their D0/D1 lines often need a level shifter or divider before an ESP32.
What you need
Shop this list19 of 20 found in our store · ₹10,838
EM-18 RFID Reader Module, 125 kHz: the part this guide coversEM-18 RFID Reader Module, 125 kHz₹280
EM4100 125kHz RFID Reader Module: another version this guide coversEM4100 125kHz RFID Reader Module₹223
ID-Innovations ID-12LA RFID Reader Module – 125kHz, EM4001 Compatible: another version this guide coversID-Innovations ID-12LA RFID Reader Module – 125kHz, EM4001 Compatible₹4,539
ID-Innovations RFID Reader Module ID-3LA 125kHz Mini – Serial/Wiegand Output: another version this guide coversID-Innovations RFID Reader Module ID-3LA 125kHz Mini – Serial/Wiegand Output₹3,909
Generic RD6300 RFID Card Reader Module – 125KHz EM4100, UART TTL RS232, 20-50mm Range: another version this guide coversRD6300 RFID Card Reader Module – 125KHz EM4100, UART TTL RS232, 20-50mm Range₹155
Generic WG26/34 125KHz RFID Contactless IP65 Smart Card Reader – ABS+PC Housing, Wiegand Output: another version this guide coversWG26/34 125KHz RFID Contactless IP65 Smart Card Reader – ABS+PC Housing, Wiegand Output₹469
JT308 USB 125KHz Proximity RFID Card Reader – Plug & Play HID Device: another version this guide coversJT308 USB 125KHz Proximity RFID Card Reader – Plug & Play HID Device₹419
Generic Blue Blank Waterproof 125KHz T5577 EM4305 Reproducible RFID ID Tag: another version this guide coversBlue Blank Waterproof 125KHz T5577 EM4305 Reproducible RFID ID Tag₹72
Generic EM4305 125KHz RFID Tag – ABS Waterproof Blank Token: another version this guide coversEM4305 125KHz RFID Tag – ABS Waterproof Blank Token₹80
Generic EM4305 125KHz RFID Tag – ABS Waterproof Keyring Token: another version this guide coversEM4305 125KHz RFID Tag – ABS Waterproof Keyring Token₹72
Generic EM4305 T5577 125KHz RFID ID Tag – White Blank Waterproof ABS Keyring: another version this guide coversEM4305 T5577 125KHz RFID ID Tag – White Blank Waterproof ABS Keyring₹82
Generic EM4305 T5577 125KHz RFID ID Tag – Yellow Blank Waterproof Keyring: another version this guide coversEM4305 T5577 125KHz RFID ID Tag – Yellow Blank Waterproof Keyring₹72
Generic EM4305/T5577 125kHz RFID ID Tag – Waterproof PVC, 25mm Diameter, 3M Back Glue: another version this guide coversEM4305/T5577 125kHz RFID ID Tag – Waterproof PVC, 25mm Diameter, 3M Back Glue₹72
Generic HT4168 125KHz RFID Coin Card – 25mm Round, K4100 Compatible, 3M Adhesive: another version this guide coversHT4168 125KHz RFID Coin Card – 25mm Round, K4100 Compatible, 3M Adhesive₹45
Generic T5577 125KHz Reproducible Coin Card – 25mm PVC: another version this guide coversT5577 125KHz Reproducible Coin Card – 25mm PVC₹70
Generic T5577 EM4305 125KHz Reproducible RFID Induction Card – PVC: another version this guide coversT5577 EM4305 125KHz Reproducible RFID Induction Card – PVC₹58
Generic T5577 RFID Card – 125kHz Reprogrammable, PVC Plastic, White: another version this guide coversT5577 RFID Card – 125kHz Reprogrammable, PVC Plastic, White₹41
Generic RW1990 Reproducible Rewritable TM Card – Inductive RFID Token: another version this guide coversRW1990 Reproducible Rewritable TM Card – Inductive RFID Token₹25
Generic Silicone RFID Wristband Tag for Access Control – 100mm Diameter: another version this guide coversSilicone RFID Wristband Tag for Access Control – 100mm Diameter₹156- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- RDM6300 RFID reader: the common UART module.
- RFID RC522: 13.56 MHz MIFARE.
- CHAFON UHF RFID: long range.
Common mistakes to avoid
- Expecting the reader to see 13.56 MHz NFC cards, which it cannot.
- Mounting the coil on a metal plate, which kills the read range.
- Connecting a 5 V reader's TX straight to a 3.3 V board.
- Treating a copied ID as a secure key for valuable access.
Frequently asked questions
Can a 125 kHz reader read my bank card or phone?
No. Bank cards, metro cards and phones use 13.56 MHz NFC, which needs an RC522 or PN532 reader instead.
How far can these readers read a tag?
Usually 2 to 8 cm with a card, and less with small keyfobs or stickers. Long-range 125 kHz readers exist but need larger antennas.
Can I copy an ID card to a new tag?
Yes, if you write the ID onto a rewritable T5577 or EM4305 tag with a writer. Plain EM4100 tags are read-only.
Is 125 kHz RFID secure enough for a door lock?
Not for anything important. The ID is sent in plain form and is easy to copy, so use it for hobby projects, attendance or low-risk doors.
Does the EM-18 work with an ESP32?
Yes. The EM-18 runs on 5 V, so put a divider on its TX line before the ESP32's 3.3 V RX pin.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



