Component guide · Intermediate · 3 min read
Elecrow Crowtail Analog Gyro

Murata ENC-03R) and Digilent Pmod GYRO (L3G4200D) Gyroscope Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A gyroscope measures how fast something is turning, in degrees per second. The Crowtail module uses a Murata ENC-03R single-axis analog gyro whose output voltage moves away from a rest value as it turns. The Digilent Pmod GYRO carries an ST L3G4200D 3-axis digital gyro on SPI or I2C. Integrating the rate gives an angle, which drifts over time without correction.
Key specs at a glance
- Axes
- 1 (ENC-03R) or 3 (L3G4200D)
- Range
- About ±300 °/s (ENC-03R), ±250 to ±2000 °/s (L3G4200D)
- Output
- Analog voltage (ENC-03R), SPI or I2C (Pmod)
- Supply
- 5 V (Crowtail), 3.3 V (Pmod)
- Sensitivity
- About 0.67 mV per °/s (ENC-03R, before amplification)
- Use
- Balancing robots, rotation sensing
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the Analog ENC-03R and Pmod GYRO gyroscopes is
A gyroscope measures how fast something turns in degrees per second; these modules give that as an analog voltage (ENC-03R) or over SPI and I2C (L3G4200D).
Gyros have an offset that drifts with temperature. Measure the rest value at start-up while the board is still and subtract it.
For angles, combine the gyro with an accelerometer (complementary filter) to stop drift.
Analog ENC-03R and Pmod GYRO gyroscopes pinout
The pins on the Analog ENC-03R and Pmod GYRO gyroscopes and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| SIG | Analog rate (Crowtail) |
| SCL / SDA / CS / SDO | Pmod GYRO bus |
| INT1 / INT2 | Interrupts (Pmod) |
- VCC
- Supply
- GND
- Ground
- SIG
- Analog rate (Crowtail)
- SCL / SDA / CS / SDO
- Pmod GYRO bus
- INT1 / INT2
- Interrupts (Pmod)
Wiring the Analog ENC-03R and Pmod GYRO gyroscopes
Connect the Analog ENC-03R and Pmod GYRO gyroscopes like this.
| Analog ENC-03R and Pmod GYRO gyroscopes pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V (Crowtail) or 3.3 V (Pmod) | 3V3 |
| GND | GND | GND |
| SIG (Crowtail) | A0 | GPIO 34 |
| SDA / SCL (Pmod) | A4 / A5 via level shifter | GPIO 21 / 22 |
- VCC
- Arduino Uno:
- 5 V (Crowtail) or 3.3 V (Pmod)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SIG (Crowtail)
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
- SDA / SCL (Pmod)
- Arduino Uno:
- A4 / A5 via level shifter
- ESP32:
- GPIO 21 / 22
Example code
Scale counts to degrees per second by turning the board a known amount. Use an L3G4200D library for the Pmod.
const int PIN = A0;
float rest = 0;
void setup() {
Serial.begin(115200);
for (int i = 0; i < 200; i++) { rest += analogRead(PIN); delay(5); } // keep still
rest /= 200;
}
void loop() {
float rate = analogRead(PIN) - rest; // counts; scale by your module's gain
Serial.println(rate);
delay(20);
}Setup and tuning
read the output while the board is still and store it as the zero-rate offset.
subtract the offset, then divide by the sensitivity to get degrees per second.
adding rate over time gives an angle, but it drifts; combine it with an accelerometer to correct drift.
power the Pmod GYRO at 3.3 V; the Crowtail module runs at 5 V on its Grove-style connector.
use a fixed loop time (for example every 10 ms) for accurate integration.
What you need
Shop this list4 of 5 found in our store · ₹3,426
Elecrow CROWTAIL Analog Gyro Sensor 2.0 – Murata ENC-03R, 1-Axis Angular Velocity, 5V: the part this guide coversElecrow CROWTAIL Analog Gyro Sensor 2.0 – Murata ENC-03R, 1-Axis Angular Velocity, 5V₹289
Digilent Pmod GYRO 3-Axis Digital Gyroscope Module – SPI/I2C Interface: another version this guide coversDigilent Pmod GYRO 3-Axis Digital Gyroscope Module – SPI/I2C Interface₹2,579- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
GY-521 MPU6050 6-axis module: the classic low-cost IMUGY-521 MPU6050 6-Axis Gyro and Accelerometer Module₹169Closest match, check the specs
Alternatives and when to choose them
- MPU6050: 3-axis gyro plus accelerometer.
- ICM-42688-P: low-noise modern IMU.
- BNO085: fused angles.
Common mistakes to avoid
- Integrating rate without removing the zero-rate offset.
- Running the 3.3 V Pmod board on 5 V logic.
- Using an irregular loop time, so the integrated angle is wrong.
- Expecting a gyro alone to give a stable tilt angle.
Frequently asked questions
Why does my angle keep drifting?
Small offset errors add up when you integrate rate. Re-zero at rest and fuse the gyro with an accelerometer.
Can a gyro alone tell me which way is down?
No. A gyro measures turning rate only; an accelerometer tells you the direction of gravity.
Is the Pmod GYRO 5 V tolerant?
No. It is a 3.3 V board, so use a level shifter with 5 V boards.
Should I use these or an MPU6050?
For new projects, an IMU such as the MPU6050 or BMI270 combines gyro and accelerometer in one cheaper chip.
What is the ENC-03R used for?
It is a single-axis analog gyro used in balancing robots and simple rotation sensing.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

