Component guide · Intermediate · 4 min read
Arducam Autofocus and High-Resolution Pi Cameras

16MP IMX519, 64MP, 108MP Kit, 21MP IMX230, 13MP IMX135 and 12MP Motorized
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These Arducam cameras add autofocus and higher resolution than the standard Pi cameras. The 16MP IMX519 is the popular choice, with NoIR and wide-angle versions; the 64MP Hawkeye takes very detailed stills; the 108MP kit is for evaluation; and the IMX230 Pivariety and IMX135 boards cover other sensors. They need Arducam's driver package before the Pi detects them.
Key specs at a glance
- Resolution
- 13MP (IMX135), 16MP (IMX519), 21MP (IMX230), 64MP, 108MP
- Focus
- Motorized autofocus or manual focus
- Interface
- MIPI CSI-2, 2 lanes
- Video
- Up to 1080p30 to 4K depending on sensor and board
- Boards
- Raspberry Pi, Jetson (some), Rock 5
- Lens
- Fixed AF lens or M12 wide angle
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arducam B0371 IMX519 Autofocus Camera Module for Raspberry Pi & Jetson Nano₹2,695
Option 2Arducam 16MP IMX519 NOIR Camera Module for Raspberry Pi₹3,599
Option 3Arducam 16MP IMX519 Camera Module with M12 Wide Angle Lens₹4,259
Option 4Arducam 16MP IMX519 Camera Module for Rock 5A & 5B₹2,874
Option 5Arducam 64MP Autofocus Camera Module for Raspberry Pi₹9,289
Option 6Arducam B0483 1/1.32″ 64MP Auto Focus Camera Module for Raspberry Pi₹6,476
What the Arducam IMX519 and 64MP autofocus cameras is
Arducam's autofocus and high-resolution cameras plug into the Raspberry Pi CSI port and add sharp focus at any distance and up to 64 MP stills.
Autofocus is controlled through libcamera: rpicam-still --autofocus-mode auto, or set AfMode in Picamera2. The 64MP sensor needs a Pi 4 or 5 with enough memory for full-size stills.
Install Arducam's driver script for your OS version first; without it the camera is not listed.
Arducam IMX519 and 64MP autofocus cameras pinout
The pins on the Arducam IMX519 and 64MP autofocus cameras and what each one does.
| Pin | Function |
|---|---|
| CSI ribbon (15 or 22-pin) | Camera data lanes, clock, I2C control and power in one flat cable |
| Metal contacts | Face the connector contacts; a reversed cable gives 'no cameras available' |
| Lens mount | Fixed, M12 or CS/C mount depending on the board |
| IR-CUT / focus motor | Driven over the same ribbon on boards that have them |
- CSI ribbon (15 or 22-pin)
- Camera data lanes, clock, I2C control and power in one flat cable
- Metal contacts
- Face the connector contacts; a reversed cable gives 'no cameras available'
- Lens mount
- Fixed, M12 or CS/C mount depending on the board
- IR-CUT / focus motor
- Driven over the same ribbon on boards that have them
Wiring the Arducam IMX519 and 64MP autofocus cameras
Turn the Pi off before connecting. Lift the connector latch, push the ribbon fully in with the contacts facing the pins, then press the latch down. The Pi 5 and Zero use the smaller 22-pin connector.
| Arducam IMX519 and 64MP autofocus cameras pin | Raspberry Pi 5 | Raspberry Pi 4 |
|---|---|---|
| Ribbon cable | CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable) | CAMERA port (15-pin) |
| Power | From the ribbon (no extra wires) | From the ribbon (no extra wires) |
| Software | rpicam-apps / Picamera2 (Bookworm) | rpicam-apps / Picamera2 (Bookworm) |
- Ribbon cable
- Raspberry Pi 5:
- CAM/DISP 0 or 1 (22-pin, use a 15-to-22 cable)
- Raspberry Pi 4:
- CAMERA port (15-pin)
- Power
- Raspberry Pi 5:
- From the ribbon (no extra wires)
- Raspberry Pi 4:
- From the ribbon (no extra wires)
- Software
- Raspberry Pi 5:
- rpicam-apps / Picamera2 (Bookworm)
- Raspberry Pi 4:
- rpicam-apps / Picamera2 (Bookworm)
Example code
Check the camera first with rpicam-hello --list-cameras. Third-party sensors usually need camera_auto_detect=0 and the right dtoverlay= line in /boot/firmware/config.txt, or the maker's driver package. Add cam.set_controls({'AfMode': 2}) for continuous autofocus.
from picamera2 import Picamera2
from picamera2.encoders import H264Encoder
import time
cam = Picamera2()
cam.configure(cam.create_still_configuration())
cam.start()
time.sleep(2) # let exposure and white balance settle
cam.capture_file("hi_res.jpg")
cam.stop()
video = cam.create_video_configuration(main={"size": (1920, 1080)})
cam.configure(video)
cam.start_recording(H264Encoder(10_000_000), "clip.h264")
time.sleep(10)
cam.stop_recording()Setup and tuning
install Arducam's driver or set the right camera overlay in config.txt (for example dtoverlay=imx519) as the guide says.
fit the cable with the contacts the right way; on a Pi 5 use the narrower 22-pin cable.
use libcamera or rpicam apps with --autofocus-mode continuous, or set a fixed lens position for steady scenes.
high-resolution capture needs a good 5 V supply; undervoltage causes frame errors.
use a lower resolution for video and the full sensor for stills.
What you need
Shop this list13 of 14 found in our store · ₹1,31,430
Arducam B0371 IMX519 Autofocus Camera Module for Raspberry Pi & Jetson Nano: the part this guide coversArducam B0371 IMX519 Autofocus Camera Module for Raspberry Pi & Jetson Nano₹2,695
Arducam 16MP IMX519 NOIR Camera Module for Raspberry Pi: another version this guide coversArducam 16MP IMX519 NOIR Camera Module for Raspberry Pi₹3,599
Arducam 16MP IMX519 Camera Module with M12 Wide Angle Lens: another version this guide coversArducam 16MP IMX519 Camera Module with M12 Wide Angle Lens₹4,259
Arducam 16MP IMX519 Camera Module for Rock 5A & 5B: another version this guide coversArducam 16MP IMX519 Camera Module for Rock 5A & 5B₹2,874
Arducam 64MP Autofocus Camera Module for Raspberry Pi: another version this guide coversArducam 64MP Autofocus Camera Module for Raspberry Pi₹9,289
Arducam B0483 1/1.32″ 64MP Auto Focus Camera Module for Raspberry Pi: another version this guide coversArducam B0483 1/1.32″ 64MP Auto Focus Camera Module for Raspberry Pi₹6,476
Arducam EK030 108MP Camera Evaluation Kit w/ Motorized Focus: another version this guide coversArducam EK030 108MP Camera Evaluation Kit w/ Motorized Focus₹36,399
Arducam B0324 Pivariety 21MP IMX230 Camera Module for Raspberry Pi & Jetson: another version this guide coversArducam B0324 Pivariety 21MP IMX230 Camera Module for Raspberry Pi & Jetson₹11,549
Arducam 13MP IMX135 MIPI Camera Module for Raspberry Pi: another version this guide coversArducam 13MP IMX135 MIPI Camera Module for Raspberry Pi₹5,129
Arducam B0273 12MP Motorized Focus Camera for Jetson Nano/Orin: another version this guide coversArducam B0273 12MP Motorized Focus Camera for Jetson Nano/Orin₹8,289
Raspberry Pi 5 (4 GB): the computer the camera plugs intoRaspberry Pi 5 16GB RAM Single Board Computer₹36,169Closest match, check the specs
Raspberry Pi 4 Model B (4 GB): works with the standard 15-pin cableRaspberry Pi 4 Model B 1GB RAM₹4,476Closest match, check the specs
15-pin to 22-pin camera cable: for Raspberry Pi 5 and Zero boardsArducam CB008 3.8cm 15-Pin to 22-Pin Camera Cable for Raspberry Pi Zero/W₹227- Camera ribbon extension cable set: to mount the camera away from the boardFind this part
Alternatives and when to choose them
- Camera Module 3: official autofocus camera.
- HQ camera IMX477: interchangeable lenses.
- 12MP IMX378 cameras: fixed focus 12MP.
Common mistakes to avoid
- Fitting the ribbon cable the wrong way round.
- Skipping the driver or overlay step, so the camera is not detected.
- Using the Pi 4 cable on a Pi 5 without the right adapter.
- Recording video at the full stills resolution.
Frequently asked questions
Does the IMX519 work with the latest Raspberry Pi OS?
Yes, with the driver or overlay Arducam lists; check their page for the current setup steps for your OS version.
Will the 64 MP camera work on a Pi Zero?
It may work at reduced performance, but a Pi 4 or Pi 5 is recommended for its memory and processing.
Can I use these cameras on a Jetson?
Some models have Jetson drivers. Check Arducam's support list for your exact camera and board.
How do I lock the focus?
Set a manual lens position with rpicam options or in Picamera2 controls, so focus stays fixed for a scene.
Why do I get a 'no cameras available' error?
Check the ribbon orientation, the overlay or driver, and that you use the right cable for the Pi model.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



