Component guide · Intermediate · 4 min read
Arduino CNC, Motor and Servo Shields

CNC Shield V3 and V4, Nano CNC Shield, Arduino Motor Shield Rev3, L298P Shields, Nano Motor Carrier, Cytron Robo Uno, Cytron Servo and G15 Shields, DFRobot Dynamixel Shield and Crowtail Motor Base
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
CNC shields hold A4988 or DRV8825 stepper drivers and run GRBL for small CNC routers, plotters and laser engravers. Motor shields drive two DC motors with an L298P H-bridge; the Arduino Motor Shield Rev3 also reads motor current. The Nano Motor Carrier and Cytron Robo Uno are robot boards, and servo shields drive many servos or smart serial servos.
Key specs at a glance
- CNC Shield V3
- 4 driver sockets (X, Y, Z, A), 12-36V motor supply, GRBL pin layout
- CNC Shield V4 / Nano
- 3 axes, for Arduino Nano
- Motor Shield Rev3
- L298P, 2 DC motors, 2A per channel, current sensing
- L298P shields
- 2 DC motors, buzzer and Bluetooth header on some
- Servo shields
- 8 RC servos, G15 or Dynamixel AX serial servos
- Nano Motor Carrier
- 4 DC motors, 4 servos, encoders, IMU, LiPo
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1CNC Shield V3 for Arduino UNO – A4988 DRV8825 Compatible₹89
Option 2Arduino CNC Shield V4 3-Axis Stepper Motor Driver₹135
Option 3CNC Shield V4 for Arduino Nano₹151
Option 4Arduino Motor Shield Rev3 A000079₹2,979
Option 5L298P Motor Driver Shield for Arduino – Dual H-Bridge₹459
Option 6Keyestudio L298P Dual Motor Driver Shield for Arduino₹529
What the Arduino CNC, motor and servo shields is
These shields add motor control to an Arduino: CNC shields hold stepper drivers for GRBL machines, and motor shields drive DC motors and servos for robots.
For CNC: flash GRBL to an Uno, fit drivers in the right orientation, set each driver's current limit, and set microstepping with the jumpers under each driver. Do not use the V4 Nano shield above 12V unless the board version says it is safe: many clones have wrong parts.
For motor shields: power the motors from the shield's screw terminal, not from USB. On the Motor Shield Rev3, cut the VIN jumper on the back if the motor supply is above 12V.
Arduino CNC, motor and servo shields pinout
The pins on the Arduino CNC, motor and servo shields and what each one does.
| Pin | Function |
|---|---|
| Driver sockets | A4988 or DRV8825 on CNC shields |
| Motor outputs | Screw terminals or 4-pin headers |
| Motor power | Separate screw terminal |
| End stops | X, Y, Z limit headers on CNC shields |
| Microstep jumpers | Under each driver |
- Driver sockets
- A4988 or DRV8825 on CNC shields
- Motor outputs
- Screw terminals or 4-pin headers
- Motor power
- Separate screw terminal
- End stops
- X, Y, Z limit headers on CNC shields
- Microstep jumpers
- Under each driver
Wiring the Arduino CNC, motor and servo shields
Never plug or unplug a stepper while powered: it destroys the driver. Fit drivers with the enable pin matching the socket marking.
| Arduino CNC, motor and servo shields pin | Connection | Note |
|---|---|---|
| Stepper | 4-pin header next to the driver | Coil pairs together |
| Motor supply | 12-24V terminal | Check polarity |
| DC motor | A+/A- or M1 terminals | Swap wires to reverse |
- Stepper
- Connection:
- 4-pin header next to the driver
- Note:
- Coil pairs together
- Motor supply
- Connection:
- 12-24V terminal
- Note:
- Check polarity
- DC motor
- Connection:
- A+/A- or M1 terminals
- Note:
- Swap wires to reverse
Example code
L298P clone shields often use pins 10, 11, 12, 13 instead: check the silkscreen. For CNC shields, flash GRBL and send G-code instead.
// Channel A: DIR 12, PWM 3, BRAKE 9. Channel B: DIR 13, PWM 11, BRAKE 8
void setup() {
pinMode(12, OUTPUT); pinMode(9, OUTPUT);
pinMode(13, OUTPUT); pinMode(8, OUTPUT);
}
void loop() {
digitalWrite(9, LOW); digitalWrite(8, LOW); // release brakes
digitalWrite(12, HIGH); digitalWrite(13, HIGH); // forward
analogWrite(3, 180); analogWrite(11, 180);
delay(2000);
digitalWrite(9, HIGH); digitalWrite(8, HIGH); // brake
delay(1000);
}Setup and tuning
feed motors from the shield's power terminal (12 to 36 V on CNC shields), not from the Arduino's USB.
adjust the A4988 or DRV8825 current limit with the pot before connecting motors.
set the jumpers under each driver, then match the steps per mm in GRBL.
fit the driver heatsinks and add a fan for long jobs.
this can destroy the stepper drivers.
What you need
Shop this list13 of 14 found in our store · ₹20,094
CNC Shield V3 for Arduino UNO – A4988 DRV8825 Compatible: the part this guide coversCNC Shield V3 for Arduino UNO – A4988 DRV8825 Compatible₹89
Arduino CNC Shield V4 3-Axis Stepper Motor Driver: another version this guide coversArduino CNC Shield V4 3-Axis Stepper Motor Driver₹135
CNC Shield V4 for Arduino Nano: another version this guide coversCNC Shield V4 for Arduino Nano₹151
Arduino Motor Shield Rev3 A000079: another version this guide coversArduino Motor Shield Rev3 A000079₹2,979
L298P Motor Driver Shield for Arduino – Dual H-Bridge: another version this guide coversL298P Motor Driver Shield for Arduino – Dual H-Bridge₹459
Keyestudio L298P Dual Motor Driver Shield for Arduino: another version this guide coversKeyestudio L298P Dual Motor Driver Shield for Arduino₹529
Arduino Nano Motor Carrier ABX00041: another version this guide coversArduino Nano Motor Carrier ABX00041₹7,709
Cytron Robo Uno Shield: another version this guide coversCytron Robo Uno Shield₹1,412
Cytron 8-Channel RC Servo Controller Shield for Arduino: another version this guide coversCytron 8-Channel RC Servo Controller Shield for Arduino₹2,078
DFRobot Smart Arduino Digital Servo Shield for Dynamixel AX: another version this guide coversDFRobot Smart Arduino Digital Servo Shield for Dynamixel AX₹2,615
Cytron G15 Shield v2.0 for Arduino: another version this guide coversCytron G15 Shield v2.0 for Arduino₹937
Elecrow Crowtail Motor Base Shield 2.0: another version this guide coversElecrow Crowtail Motor Base Shield 2.0₹824- Uno R3 development board: the controller used in the wiring tableFind this part
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- L298N motor driver: the module version.
- DRV8825 stepper driver: drivers for CNC shields.
- PCA9685 servo driver: 16 servos over I2C.
Common mistakes to avoid
- Unplugging a stepper motor while the driver is powered.
- Running motors from USB power through the Arduino.
- Using drivers with no current setting and overheating them.
- Forgetting the microstep jumpers, so distances come out wrong.
Frequently asked questions
What firmware runs on the CNC Shield V3?
GRBL on an Arduino Uno. You send G-code from a sender such as Universal G-code Sender or Candle.
Can the CNC shield drive DC motors?
No. It holds stepper drivers. Use a motor shield such as the L298P for DC motors.
How do I set the stepper current?
Measure the reference voltage on the driver pot and set it from the formula for your driver and motor rating.
Why do the motors vibrate but not turn?
Check the coil pairing in the motor wiring, the current setting and that the steps per mm are not set far too high.
Can the Motor Shield Rev3 drive two motors from 12 V?
Yes, up to about 2 A per channel, with the motor supply on the external power terminals.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

