Component guide · Intermediate · 5 min read
Arduino Communication Shields

W5100 and W5200 Ethernet, Nano ENC28J60, USB Host Shield, CAN-BUS Shields, RS485 Shield, XBee Shields, ESP8266 Wi-Fi Shields, Dragino and 915 MHz LoRa Shields, Bluno Bee and UNO SPE Shield
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Communication shields add a network or bus to an Arduino. W5100 and W5200 Ethernet shields work with the standard Ethernet library; the Nano ENC28J60 needs the heavier EthernetENC library. The USB host shield reads keyboards, game pads and phones. CAN-BUS shields use the MCP2515; the RS485 shield talks Modbus. XBee, ESP8266 and LoRa shields add wireless links.
Key specs at a glance
- Ethernet
- W5100 and W5200 (hardware TCP/IP), ENC28J60 (software stack)
- USB host
- MAX3421E, USB Host Shield 2.0 library
- CAN
- MCP2515 with TJA1050 or MCP2551, DB9 connector
- RS485
- MAX485-type transceiver, auto or manual direction
- Wireless
- XBee socket, ESP8266 (ESP-12 or ESP-13), SX1276 LoRa, Bluno Bee BLE
- SPE
- UNO SPE Shield: 10BASE-T1S single pair Ethernet
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino W5100 Ethernet Shield with Micro SD Slot₹422
Option 2W5100 R3 Ethernet & SD Shield for Arduino₹1,103
Option 3DFRobot W5200 Ethernet Shield for Arduino UNO/Mega₹2,089
Option 4Nano ENC28J60 Ethernet Shield V1.0₹519
Option 5ADK USB Host Shield for Arduino – MAX3421E Compatible₹649
Option 6Mini USB Host Shield 2.0 ADK for Arduino Pro Mini₹679
What the Arduino Ethernet, USB host, CAN, RS485, XBee, Wi-Fi and LoRa shields is
Communication shields give an Arduino a network or bus connection, such as Ethernet, USB host, CAN, RS485 or a wireless radio, on a plug-in board.
Most of these shields use SPI with pin 10 (or another pin) as chip select. When stacking an Ethernet shield with an SD card and another SPI shield, set every unused chip select pin HIGH so they do not talk at once.
ESP8266 shields run their own firmware: either use AT commands from the Arduino over serial, or program the ESP8266 directly and treat the Arduino as an I/O board. LoRa shields must match your region: 865-867 MHz in India.
Arduino Ethernet, USB host, CAN, RS485, XBee, Wi-Fi and LoRa shields pinout
The pins on the Arduino Ethernet, USB host, CAN, RS485, XBee, Wi-Fi and LoRa shields and what each one does.
| Pin | Function |
|---|---|
| Uno R3 headers | D0-D13, A0-A5, power pins and the IOREF pin |
| ICSP header | SPI on 6 pins, used by many shields |
| IOREF | Tells the shield whether the board is 5V or 3.3V |
| Stacking headers | Let another shield sit on top |
| Reset button | Repeated on top of most shields |
- Uno R3 headers
- D0-D13, A0-A5, power pins and the IOREF pin
- ICSP header
- SPI on 6 pins, used by many shields
- IOREF
- Tells the shield whether the board is 5V or 3.3V
- Stacking headers
- Let another shield sit on top
- Reset button
- Repeated on top of most shields
Wiring the Arduino Ethernet, USB host, CAN, RS485, XBee, Wi-Fi and LoRa shields
Fit the LoRa antenna before powering the radio. Check UART jumpers on XBee and ESP8266 shields so they do not clash with USB upload.
| Arduino Ethernet, USB host, CAN, RS485, XBee, Wi-Fi and LoRa shields pin | Connection | Note |
|---|---|---|
| Ethernet | RJ45 to router | Pin 10 = Ethernet CS, pin 4 = SD CS |
| CAN | CAN-H and CAN-L, 120 ohm at both ends | Common ground |
| RS485 | A and B to the bus | Terminate long buses |
- Ethernet
- Connection:
- RJ45 to router
- Note:
- Pin 10 = Ethernet CS, pin 4 = SD CS
- CAN
- Connection:
- CAN-H and CAN-L, 120 ohm at both ends
- Note:
- Common ground
- RS485
- Connection:
- A and B to the bus
- Note:
- Terminate long buses
Example code
Open the serial monitor to see the IP address, then open it in a browser on the same network.
#include <SPI.h>
#include <Ethernet.h>
byte mac[] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0x01};
EthernetServer server(80);
void setup() {
Serial.begin(9600);
Ethernet.begin(mac); // DHCP
server.begin();
Serial.println(Ethernet.localIP());
}
void loop() {
EthernetClient c = server.available();
if (!c) return;
while (c.connected() && c.available()) c.read();
c.println("HTTP/1.1 200 OK\r\nContent-Type: text/plain\r\n");
c.print("A0 = "); c.println(analogRead(A0));
c.stop();
}Setup and tuning
Ethernet shields use SPI and pin 10 (plus pin 4 for SD). Do not use those pins for anything else.
use Ethernet for W5100 and W5200, EthernetENC for ENC28J60, mcp_can for MCP2515 and ModbusMaster for RS485.
set the MCP2515 crystal (8 or 16 MHz) and bitrate in code to match the shield and the bus.
use 120 Ω termination at the two ends of a long RS485 or CAN bus only.
make sure two stacked shields do not both use the same CS or interrupt pin.
What you need
Shop this list19 of 20 found in our store · ₹24,615
Arduino W5100 Ethernet Shield with Micro SD Slot: the part this guide coversArduino W5100 Ethernet Shield with Micro SD Slot₹422
W5100 R3 Ethernet & SD Shield for Arduino: another version this guide coversW5100 R3 Ethernet & SD Shield for Arduino₹1,103
DFRobot W5200 Ethernet Shield for Arduino UNO/Mega: another version this guide coversDFRobot W5200 Ethernet Shield for Arduino UNO/Mega₹2,089
Nano ENC28J60 Ethernet Shield V1.0: another version this guide coversNano ENC28J60 Ethernet Shield V1.0₹519
ADK USB Host Shield for Arduino – MAX3421E Compatible: another version this guide coversADK USB Host Shield for Arduino – MAX3421E Compatible₹649
Mini USB Host Shield 2.0 ADK for Arduino Pro Mini: another version this guide coversMini USB Host Shield 2.0 ADK for Arduino Pro Mini₹679
CAN-BUS Shield V2.0 for Arduino: another version this guide coversCAN-BUS Shield V2.0 for Arduino₹3,879
Elecrow CAN-BUS Shield V1.5 for Arduino: another version this guide coversElecrow CAN-BUS Shield V1.5 for Arduino₹769
DFRobot RS485 Shield for Arduino: another version this guide coversDFRobot RS485 Shield for Arduino₹939
Cytron XBee Shield for Arduino: another version this guide coversCytron XBee Shield for Arduino₹734
XBee Adapter Shield Breakout Board: another version this guide coversXBee Adapter Shield Breakout Board₹134
XBee IO Expansion Shield: another version this guide coversXBee IO Expansion Shield₹1,153
XBee Shield V03 for Arduino Wireless Module: another version this guide coversXBee Shield V03 for Arduino Wireless Module₹140
ESP8266 Web Server WiFi Shield for Arduino ESP-13: another version this guide coversESP8266 Web Server WiFi Shield for Arduino ESP-13₹239
ESP8266 WiFi Shield Module for Arduino: another version this guide coversESP8266 WiFi Shield Module for Arduino₹239
Dragino LoRa Shield for Arduino V95: another version this guide coversDragino LoRa Shield for Arduino V95₹3,671
Lora Shield 915MHz for Arduino UNO, Mega, Leonardo: another version this guide coversLora Shield 915MHz for Arduino UNO, Mega, Leonardo₹2,049
DFRobot Bluno Bee – Arduino Bluetooth 4.0 BLE Module: another version this guide coversDFRobot Bluno Bee – Arduino Bluetooth 4.0 BLE Module₹1,009
Arduino UNO SPE Shield: another version this guide coversArduino UNO SPE Shield₹4,199- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- W5500 Ethernet module: newer, faster chip.
- CAN-BUS MCP2515: the module version.
- XBee and Zigbee: XBee radios.
Common mistakes to avoid
- Using pin 10 for something else on an Ethernet shield.
- Setting the wrong MCP2515 crystal frequency in code.
- Adding termination resistors at every node of the bus.
- Stacking two shields that use the same CS pin.
Frequently asked questions
Which Ethernet shield is easiest for beginners?
The W5100 or W5500-based shields work with the standard Ethernet library and handle TCP/IP in hardware.
Can I read my car's data with a CAN shield?
Yes, through the OBD-II port with the right cable, but read only and never send messages to a moving vehicle.
Why does my CAN shield receive nothing?
Check the bitrate, the crystal setting in code, CAN-H and CAN-L wiring and the 120 Ω termination.
Can I use an Ethernet and an SD card together?
Yes. They share SPI with separate CS pins (10 and 4); set the unused one high when talking to the other.
What does the USB host shield do?
It lets the Arduino read USB devices such as keyboards, game pads and some phones.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


