Component guide · Beginner · 4 min read
Arduino Learning and Data Shields

Multifunction Shield, 9-in-1 Expansion Board, Adafruit and Generic Data Logging Shields, Arduino 4 Relay Shield, 9 Axis Motion Shield, Cytron Easy MP3 Shield, VS1053 MP3 Board and Olimex DUINOMITE-IO
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These shields add a whole set of parts in one plug-in board. The multifunction shield has a 4-digit display, LEDs, buttons, a buzzer and a potentiometer for learning. Data logging shields add an SD card and a real-time clock to save timed readings. The 4 relay shield switches loads, the 9 axis motion shield adds a BNO055 IMU, and MP3 shields play audio from an SD card.
Key specs at a glance
- Multifunction
- 4-digit 7-segment, 4 LEDs, 3 buttons, buzzer, pot
- 9-in-1 board
- Sensors, LEDs, buzzer, IR and buttons
- Data logging
- SD card (SPI, CS on pin 10) and DS1307 or PCF8523 RTC
- 4 Relay Shield
- 4 relays, 48V DC or 30V AC max contacts
- 9 Axis Motion
- Bosch BNO055 with sensor fusion
- MP3
- VS1053 codec, SD card, headphone jack
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Uno Leonardo Multifunction Shield₹117
Option 29-in-1 Multi-function Expansion Board for Arduino UNO₹409
Option 3Adafruit Data Logging Shield for Arduino₹1,899
Option 4Arduino Data Logger Shield w/ SD Card & RTC₹131
Option 5Arduino 4 Relay Shield₹2,979
Option 6Arduino 9 Axis Motion Shield A000070₹4,269
What the Arduino multifunction, data logging, relay, motion and MP3 shields is
These shields put a set of parts on one plug-in board: displays, buttons and buzzers for learning, or an SD card and real-time clock for logging data.
The multifunction shield is a classroom favourite: all parts are fixed, so students focus on code. Its display uses two 74HC595 shift registers.
For logging, format the SD card as FAT32, set the RTC once from your computer's time, and close or flush the file after each write so data survives a power cut. The Arduino 4 Relay Shield's contacts are rated for low-voltage loads only; it is not meant for mains.
Arduino multifunction, data logging, relay, motion and MP3 shields pinout
The pins on the Arduino multifunction, data logging, relay, motion and MP3 shields and what each one does.
| Pin | Function |
|---|---|
| SD card | SPI with CS on D10 (D4 on some) |
| RTC | I2C on A4/A5 or SDA/SCL |
| Relays | D4, D7, D8, D12 on the Arduino 4 Relay Shield |
| Multifunction display | Latch D4, clock D7, data D8 |
| VS1053 | SPI plus DREQ and two chip selects |
- SD card
- SPI with CS on D10 (D4 on some)
- RTC
- I2C on A4/A5 or SDA/SCL
- Relays
- D4, D7, D8, D12 on the Arduino 4 Relay Shield
- Multifunction display
- Latch D4, clock D7, data D8
- VS1053
- SPI plus DREQ and two chip selects
Wiring the Arduino multifunction, data logging, relay, motion and MP3 shields
Fit the RTC coin cell before setting the time. Keep relay loads within the contact rating.
| Arduino multifunction, data logging, relay, motion and MP3 shields pin | Connection | Note |
|---|---|---|
| SD card | Into the slot, FAT32 | Under 32 GB is safest |
| Relay load | COM and NO terminals | Low voltage only |
| Headphones | 3.5 mm jack on MP3 boards | Not a speaker |
- SD card
- Connection:
- Into the slot, FAT32
- Note:
- Under 32 GB is safest
- Relay load
- Connection:
- COM and NO terminals
- Note:
- Low voltage only
- Headphones
- Connection:
- 3.5 mm jack on MP3 boards
- Note:
- Not a speaker
Example code
Check which RTC chip your shield has (DS1307 or PCF8523) and change the class name. Some clones use D4 for SD chip select.
#include <SPI.h>
#include <SD.h>
#include <RTClib.h>
RTC_DS1307 rtc; // RTC_PCF8523 on Adafruit Rev B shields
void setup() {
Serial.begin(9600);
rtc.begin();
if (!rtc.isrunning()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));
if (!SD.begin(10)) Serial.println("SD failed");
}
void loop() {
DateTime t = rtc.now();
File f = SD.open("log.csv", FILE_WRITE);
if (f) {
f.print(t.unixtime()); f.print(','); f.println(analogRead(A0));
f.close();
}
delay(5000);
}Setup and tuning
format cards as FAT32 and use the SD library with CS on pin 10 (check the shield).
fit a coin cell so the clock keeps time while unplugged, then set the time once from your computer.
use the library or shift-register code for the 4-digit display; it uses 74HC595 chips.
call flush() or close the log file regularly, or data is lost when power fails.
keep the contacts within their rating and keep mains wiring out of reach.
What you need
Shop this list9 of 10 found in our store · ₹12,577
Arduino Uno Leonardo Multifunction Shield: the part this guide coversArduino Uno Leonardo Multifunction Shield₹117
9-in-1 Multi-function Expansion Board for Arduino UNO: another version this guide covers9-in-1 Multi-function Expansion Board for Arduino UNO₹409
Adafruit Data Logging Shield for Arduino: another version this guide coversAdafruit Data Logging Shield for Arduino₹1,899
Arduino Data Logger Shield w/ SD Card & RTC: another version this guide coversArduino Data Logger Shield w/ SD Card & RTC₹131
Arduino 4 Relay Shield: another version this guide coversArduino 4 Relay Shield₹2,979
Arduino 9 Axis Motion Shield A000070: another version this guide coversArduino 9 Axis Motion Shield A000070₹4,269
Cytron Easy MP3 Shield for Arduino: another version this guide coversCytron Easy MP3 Shield for Arduino₹1,590
VS1053 MP3 Recording Module Development Board: another version this guide coversVS1053 MP3 Recording Module Development Board₹659
Olimex DUINOMITE-IO Extension Board: another version this guide coversOlimex DUINOMITE-IO Extension Board₹524- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- DS3231 RTC: a more accurate clock.
- BNO055 IMU: the motion shield's sensor.
- 5V relay module: single relay boards.
Common mistakes to avoid
- Formatting the SD card as exFAT.
- Running the RTC with no coin cell.
- Leaving the log file open, so data is lost on power cut.
- Switching mains loads beyond the relay contact rating.
Frequently asked questions
Why does my data logging shield fail to start the SD card?
Check the card is FAT32, the CS pin matches the shield, and the card is fully inserted.
Why does the clock reset every time I unplug it?
The RTC needs a coin cell. Fit the battery and set the time once.
Can I use the multifunction shield with sensors?
Yes, on the free pins, but the display and buttons use several pins, so check the shield's pin map.
How often should I write to the SD card?
Write each reading but flush or close the file every few writes, so a power cut loses little data.
Can the 4 relay shield switch mains?
Its contacts are rated for low voltage on many versions; check the rating and keep mains wiring enclosed.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

