Component guide · Advanced · 3 min read
Bosch BHI260AP, BHI260AB, BHI160 and BHI160B Smart Sensor Hubs

and the LilyGO T-BHI260AP Board
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The BHI260AP and BHI260AB combine a 6-axis IMU with a low-power 32-bit processor that runs sensor fusion, step counting and self-learning activity recognition, so the main microcontroller can sleep. The BHI160 and BHI160B are the earlier generation. They need a firmware image loaded at start-up. The LilyGO T-BHI260AP board pairs one with an ESP32 for quick testing.
Key specs at a glance
- Sensors
- 6-axis accelerometer and gyroscope
- Processor
- 32-bit Fuser2 core (BHI260), runs fusion and AI
- Outputs
- Orientation, game rotation, steps, activity, gestures
- Interface
- I2C or SPI host; second bus for extra sensors
- Supply
- 1.8 V core, 1.8 to 3.3 V I/O
- Power
- Very low, suits wearables
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Bosch Sensortec BHI260AP 6-Axis Smart IMU Sensor, Accel + Gyro, AI Sensor Hub, 32-bit MCU, I2C/SPI, 1.8V, 44-LGA₹899
Option 2Bosch BHI260AB Smart Sensor Hub, 6-Axis IMU + 32-bit MCU (Fuser2), Ultra-Low Power, Sensor Fusion, I²C/SPI, LGA-44₹1,679
Option 3LilyGO T-BHI260AP AI Smart Sensor Module – ESP32 with Bosch BHI260AP IMU₹719
Option 4Bosch BHI160 6-Axis Smart Motion Sensor Hub with Accelerometer & Gyroscope, I²C, –40°C to 85°C, 1.6V~3.3V₹409
Option 5Bosch Sensortec BHI160B LGA-24 6-Axis Accelerometer Gyroscope₹675
What the Bosch BHI260AP and BHI160 smart sensor hubs is
The Bosch BHI260 and BHI160 are smart sensor hubs: a 6-axis IMU with its own processor that runs orientation fusion and activity detection, so the host can sleep.
A sensor hub does the maths on its own core. You ask for a virtual sensor such as rotation vector and it reports ready values at the rate you choose.
You must upload Bosch's firmware over I2C or SPI at each power-up (or store it in a flash chip). The LilyGO board's examples do this for you.
Bosch BHI260AP and BHI160 smart sensor hubs pinout
The pins on the Bosch BHI260AP and BHI160 smart sensor hubs and what each one does.
| Pin | Function |
|---|---|
| VDD / VDDIO | Supply |
| GND | Ground |
| SCL / SDA or SPI | Host bus |
| HIRQ | Host interrupt |
| RESETN | Reset |
| M2 / M3 | Secondary bus for magnetometer, flash |
- VDD / VDDIO
- Supply
- GND
- Ground
- SCL / SDA or SPI
- Host bus
- HIRQ
- Host interrupt
- RESETN
- Reset
- M2 / M3
- Secondary bus for magnetometer, flash
Wiring the Bosch BHI260AP and BHI160 smart sensor hubs
Bare chips are 1.8 V core with 1.8 to 3.3 V I/O and need a PCB. The LilyGO board has an ESP32 already wired.
| Bosch BHI260AP and BHI160 smart sensor hubs pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
After it shows up, load the firmware and read virtual sensors with Bosch's BHY2 SensorAPI or the LilyGO SensorLib examples.
#include <Wire.h>
void setup() {
Serial.begin(115200);
Wire.begin();
for (uint8_t a = 1; a < 127; a++) {
Wire.beginTransmission(a);
if (Wire.endTransmission() == 0) { Serial.print("Found 0x"); Serial.println(a, HEX); }
}
Serial.println("BHI260 is usually 0x28 or 0x29");
}
void loop() {}Setup and tuning
the hub needs its firmware loaded over I2C or SPI at every power-up; use Bosch's library or the LilyGO examples.
enable only the outputs you need, such as game rotation or step counter, to save power.
use the INT pin to wake the host when new data or events arrive, instead of polling.
move the board in a figure of eight and keep it still so the fusion settles.
run at 1.8 to 3.3 V as specified; the LilyGO board has its own regulator.
What you need
Shop this list7 of 8 found in our store · ₹9,365
Bosch Sensortec BHI260AP 6-Axis Smart IMU Sensor, Accel + Gyro, AI Sensor Hub, 32-bit MCU, I2C/SPI, 1.8V, 44-LGA: the part this guide coversBosch Sensortec BHI260AP 6-Axis Smart IMU Sensor, Accel + Gyro, AI Sensor Hub, 32-bit MCU, I2C/SPI, 1.8V, 44-LGA₹899
Bosch BHI260AB Smart Sensor Hub, 6-Axis IMU + 32-bit MCU (Fuser2), Ultra-Low Power, Sensor Fusion, I²C/SPI, LGA-44: another version this guide coversBosch BHI260AB Smart Sensor Hub, 6-Axis IMU + 32-bit MCU (Fuser2), Ultra-Low Power, Sensor Fusion, I²C/SPI, LGA-44₹1,679
LilyGO T-BHI260AP AI Smart Sensor Module – ESP32 with Bosch BHI260AP IMU: another version this guide coversLilyGO T-BHI260AP AI Smart Sensor Module – ESP32 with Bosch BHI260AP IMU₹719
Bosch BHI160 6-Axis Smart Motion Sensor Hub with Accelerometer & Gyroscope, I²C, –40°C to 85°C, 1.6V~3.3V: another version this guide coversBosch BHI160 6-Axis Smart Motion Sensor Hub with Accelerometer & Gyroscope, I²C, –40°C to 85°C, 1.6V~3.3V₹409
Bosch Sensortec BHI160B LGA-24 6-Axis Accelerometer Gyroscope: another version this guide coversBosch Sensortec BHI160B LGA-24 6-Axis Accelerometer Gyroscope₹675
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- BNO085 IMU module: gives ready-made orientationFind this part
Adafruit BNO055 9-DOF fusion breakout: orientation without your own filterAdafruit BNO055 9-DOF Absolute Orientation IMU Fusion Breakout – STEMMA QT / Qwiic₹4,595Closest match, check the specs
Alternatives and when to choose them
Common mistakes to avoid
- Forgetting to upload the hub firmware at power-up.
- Polling constantly instead of using the interrupt pin.
- Enabling every virtual sensor and wasting power.
- Using a plain IMU library that cannot talk to the hub.
Frequently asked questions
Why does the BHI260 need firmware?
It is a programmable processor. The firmware tells it which fusion and AI features to run.
Can I use it with Arduino?
Yes, with Bosch's library or the LilyGO T-BHI260AP examples for ESP32.
What is the benefit over a plain IMU?
It runs the fusion itself, so your main chip can sleep and the battery lasts much longer.
Can it count steps?
Yes. Step counting and activity recognition are built-in virtual sensors.
BHI260AP or BHI260AB, which one?
The AP has self-learning activity features; the AB is the general-purpose version.
Parts for this guide
Bosch Sensortec BHI260AP 6-Axis Smart IMU Sensor, Accel + Gyro, AI Sensor Hub, 32-bit MCU, I2C/SPI, 1.8V, 44-LGA₹899View
Bosch BHI260AB Smart Sensor Hub, 6-Axis IMU + 32-bit MCU (Fuser2), Ultra-Low Power, Sensor Fusion, I²C/SPI, LGA-44₹1,679View- ₹719View
Bosch BHI160 6-Axis Smart Motion Sensor Hub with Accelerometer & Gyroscope, I²C, –40°C to 85°C, 1.6V~3.3V₹409View- ₹675View
- ₹389View
- ₹2,209View
- ₹4,595View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

