Component guide · Advanced · 4 min read
CubeMars Robot Actuators

AK60-6, AK70-10, AK80-9 V3, AK80-64 and AK10-9 V2 Planetary Joint Motors with Driver, RI80 and RI100 Inner Runner Frameless Motors with Hall Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
CubeMars AK actuators combine a brushless motor, planetary gearbox, encoder and FOC driver in one compact joint. They take position, speed, torque or MIT-mode commands over CAN bus, which makes them popular for legged robots, exoskeletons and robot arms. The number after the dash is the gear ratio: AK80-9 is 9:1 and quick, AK80-64 is 64:1 and strong. RI80 and RI100 are frameless motors you build into your own joint.
Key specs at a glance
- Gear ratio
- 6:1 (AK60-6) to 64:1 (AK80-64)
- Peak torque
- About 9 Nm (AK60-6) to 120 Nm (AK80-64)
- Voltage
- 24V or 48V
- Control
- CAN bus, servo and MIT modes; UART for setup
- Feedback
- Absolute encoder, position, speed, current
- RI series
- Frameless inner runner with Hall sensors, needs your driver
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1T-Motor AK60-6 V1.1 80KV Cube Mars Motor₹33,919
Option 2T-Motor AK70-10 KV100 Brushless Robot Motor (Without Driver)₹53,299
Option 3T-Motor AK80-64 Legged Robot Power Actuator – KV80₹1,04,639
Option 4T-Motor CubeMars AK10-9 V2.0 100KV Brushless DC Actuator Robot Joint Motor₹1,00,113
Option 5T-Motor CubeMars Ak80-9 V3.0 100KV Brushless DC Actuator Robot Joint Motor₹79,739
Option 6T-Motor CubeMars RI100 KV105 Brushless DC Inner Runner Robot Joint Motor (with Hall sensor)₹20,615
What the T-Motor CubeMars AK and RI robot joint actuators is
CubeMars AK actuators combine a brushless motor, planetary gearbox, encoder and driver in one joint that takes position, speed or torque commands over CAN.
Use AK80-9 or AK70-10 for fast quasi-direct-drive leg joints, AK10-9 for higher torque, and AK80-64 for slow, strong joints like elbows. Connect CAN-H, CAN-L and a common ground from a CAN adapter or a microcontroller with a CAN transceiver, and set each motor's ID with the CubeMars upper computer software.
These joints are strong enough to injure. Start with low gains and torque limits, fit a hardware power cut, and keep hands away during testing.
T-Motor CubeMars AK and RI robot joint actuators pinout
The pins on the T-Motor CubeMars AK and RI robot joint actuators and what each one does.
| Pin | Function |
|---|---|
| Power | XT30 24V or 48V |
| CAN-H / CAN-L | Bus to controller |
| GND | Common reference |
| UART | Setup and firmware |
| Encoder | Built in |
- Power
- XT30 24V or 48V
- CAN-H / CAN-L
- Bus to controller
- GND
- Common reference
- UART
- Setup and firmware
- Encoder
- Built in
Wiring the T-Motor CubeMars AK and RI robot joint actuators
Give every motor a unique CAN ID before putting several on one bus.
| T-Motor CubeMars AK and RI robot joint actuators pin | Connection | Note |
|---|---|---|
| CAN-H / CAN-L | CAN transceiver (e.g. SN65HVD230) | 120 ohm at both bus ends |
| Power | 24V or 48V supply | With emergency stop |
| GND | Controller GND | Common |
- CAN-H / CAN-L
- Connection:
- CAN transceiver (e.g. SN65HVD230)
- Note:
- 120 ohm at both bus ends
- Power
- Connection:
- 24V or 48V supply
- Note:
- With emergency stop
- GND
- Connection:
- Controller GND
- Note:
- Common
Example code
Command formats differ between servo mode and MIT mode; follow the CubeMars manual for your firmware version.
1. Connect the motor to the CubeMars upper computer over the USB-UART adapter.
2. Set the CAN ID, baud rate (1 Mbps typical) and control mode.
3. Calibrate the encoder with the output free to turn.
4. Wire CAN to your controller with 120 ohm termination.
5. Send enter-motor-mode, then small position commands with low Kp and Kd.
6. Raise gains slowly; always have an emergency stop on the power.Setup and tuning
use a 24 V or 48 V supply that can deliver peak current, with a fuse and an emergency stop.
connect CAN-H and CAN-L with 120 Ω at the ends, and give each actuator its own ID.
use CubeMars' upper computer software over UART to set IDs, zero position and limits.
test MIT mode with low stiffness and damping before raising them.
fit hard stops so a software bug cannot over-rotate a joint.
What you need
Shop this list9 of 9 found in our store · ₹4,15,241
T-Motor AK60-6 V1.1 80KV Cube Mars Motor: the part this guide coversT-Motor AK60-6 V1.1 80KV Cube Mars Motor₹33,919
T-Motor AK70-10 KV100 Brushless Robot Motor (Without Driver): another version this guide coversT-Motor AK70-10 KV100 Brushless Robot Motor (Without Driver)₹53,299
T-Motor AK80-64 Legged Robot Power Actuator – KV80: another version this guide coversT-Motor AK80-64 Legged Robot Power Actuator – KV80₹1,04,639
T-Motor CubeMars AK10-9 V2.0 100KV Brushless DC Actuator Robot Joint Motor: another version this guide coversT-Motor CubeMars AK10-9 V2.0 100KV Brushless DC Actuator Robot Joint Motor₹1,00,113
T-Motor CubeMars Ak80-9 V3.0 100KV Brushless DC Actuator Robot Joint Motor: another version this guide coversT-Motor CubeMars Ak80-9 V3.0 100KV Brushless DC Actuator Robot Joint Motor₹79,739
T-Motor CubeMars RI100 KV105 Brushless DC Inner Runner Robot Joint Motor (with Hall sensor): another version this guide coversT-Motor CubeMars RI100 KV105 Brushless DC Inner Runner Robot Joint Motor (with Hall sensor)₹20,615
T-Motor CubeMars RI80 KV75 Brushless DC Inner Runner Robot Joint Motor (with Hall sensor): another version this guide coversT-Motor CubeMars RI80 KV75 Brushless DC Inner Runner Robot Joint Motor (with Hall sensor)₹22,691
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- BLDC motors and ESCs: motor basics.
- SimpleFOC mini BLDC driver: drive your own motors.
- Linear actuators and solenoids: straight-line motion.
Common mistakes to avoid
- Testing with high gains before checking direction and limits.
- Giving two actuators the same CAN ID.
- Running without an emergency stop.
- Using a supply that cannot deliver peak current.
Frequently asked questions
Can I control AK actuators with an Arduino?
Yes, with a CAN module, but an ESP32 with TWAI or a Teensy is more common.
What is MIT mode?
A control mode where you send position, speed, stiffness, damping and torque in one command.
Why does my actuator jerk at start-up?
The gains are too high or the zero position is not set. Start with low gains.
Which actuator suits a small legged robot?
The AK60-6 and AK70-10 are common for small legged robots and arms.
Do I need a separate driver?
No. The driver is built into the actuator.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
