Component guide · Beginner · 3 min read
12V Electric Linear Actuators (1000N and Mini Fast 100N)

Wiring, Limits and Control
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 12 V linear actuator is a DC motor driving a lead screw that pushes a rod in and out. The heavy 1000 N type is slow and strong for hatches, beds and lifts; the mini fast 100 N type moves quickly for light mechanisms. Built-in limit switches stop it at each end. Reverse polarity to reverse direction, using two relays or an H-bridge.
Key specs at a glance
- Voltage
- 12 V DC
- Force
- 1000 N (heavy) or 100 N (mini fast)
- Speed
- About 5 to 10 mm/s (1000 N), about 90 mm/s (mini)
- Stroke
- 50 mm and other lengths
- Current
- About 1 to 3 A under load
- Limits
- Built-in end switches
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Electric Linear Actuator 12V₹3,780
Option 2Mini Fast Linear Actuator 12V₹3,799
What the 12V electric linear actuator is
A linear actuator is a DC motor and gearbox that turns a lead screw, so a rod moves in and out in a straight line. Limit switches inside stop it at each end of its stroke.
The lead screw holds position when power is off, so it will not back-drive under load. Because limit switches cut the motor, the driver sees no current at the ends, which is how code can detect the end.
Speed falls under load; force rating is the maximum, not the working load.
12V electric linear actuator pinout
The pins on the 12V electric linear actuator and what each one does.
| Pin | Function |
|---|---|
| Red | Motor lead (+ to extend on most) |
| Black | Motor lead |
- Red
- Motor lead (+ to extend on most)
- Black
- Motor lead
Wiring the 12V electric linear actuator
Connect the 12V electric linear actuator like this.
| 12V electric linear actuator pin | Uno + driver | ESP32 + driver |
|---|---|---|
| Actuator leads | BTS7960 or L298N outputs | BTS7960 outputs |
| Driver inputs | D5 / D6 PWM | GPIO 25 / 26 |
| Supply | 12 V, 3 A or more | Same |
- Actuator leads
- Uno + driver:
- BTS7960 or L298N outputs
- ESP32 + driver:
- BTS7960 outputs
- Driver inputs
- Uno + driver:
- D5 / D6 PWM
- ESP32 + driver:
- GPIO 25 / 26
- Supply
- Uno + driver:
- 12 V, 3 A or more
- ESP32 + driver:
- Same
Example code
Run time should be a little longer than a full stroke, since the limit switch stops it.
const int RPWM = 5, LPWM = 6;
void move(int speed) { // + extend, - retract
analogWrite(RPWM, speed > 0 ? speed : 0);
analogWrite(LPWM, speed < 0 ? -speed : 0);
}
void setup() {}
void loop() { move(255); delay(8000); move(-255); delay(8000); move(0); delay(2000); }Setup and tuning
reverse it with two relays (H-bridge wiring) or a motor driver rated above its stall current, such as a BTS7960.
use the clevis pins at both ends so it can pivot; side loads bend the rod.
the limit switches cut the motor at each end, so current drops to zero there.
size the 12 V supply for the stall current, not the running current.
two actuators side by side drift apart; use feedback actuators if they must stay in sync.
What you need
Shop this list8 of 9 found in our store · ₹8,827
Electric Linear Actuator 12V: the part this guide coversElectric Linear Actuator 12V₹3,780
Mini Fast Linear Actuator 12V: another version this guide coversMini Fast Linear Actuator 12V₹3,799- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
BTS7960 43A H-bridge motor driver: to run it both ways with speed controlBTS7960 43A High-Current H-Bridge Motor Driver₹344Closest match, check the specs
L298N dual H-bridge motor driver module: to reverse itL298N Dual H-Bridge Motor Driver Module₹128
5V relay module with optocoupler: to switch it from a microcontroller5V Relay Module with Optocoupler₹74
SMPS power supply in metal enclosure (5/12/24 V): a 12 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Limit and micro switch: end-of-travel detectionLimit and Micro Switch₹15
Alternatives and when to choose them
- Linear actuators and solenoids.
- BTS7960 driver.
- Stepper motors: precise positioning.
Common mistakes to avoid
- Side-loading the rod, which bends it or wears the seals.
- Using a small driver that cannot handle the stall current.
- Expecting two actuators to stay in sync without feedback.
- Working at the maximum force rating all the time.
Frequently asked questions
Does a linear actuator hold its position without power?
Yes. The lead screw does not back-drive, so it holds the load when power is off.
Do these actuators give position feedback?
Not these models. Choose a version with a potentiometer or Hall sensor if you need to know the position.
Can I control the speed?
Yes. PWM through a motor driver slows it down; it also slows under heavy load.
How do I reverse a linear actuator?
Reverse the polarity, using a DPDT switch, two relays or an H-bridge driver.
Is it waterproof?
Check the IP rating on the label. Many cheap actuators are only splash-resistant.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

