Component guide · Beginner · 3 min read
Emax ES08A, ES08MA II and ES08D Micro Servos

Specs, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Emax ES08 family are 8 to 12 g micro servos, a step up from the SG90 in precision and gear life. ES08A has plastic gears, ES08MA II has metal gears, and ES08D is a digital version with faster response and stronger holding. They take the usual 50 Hz PWM signal and run from 4.8 to 6 V, so any servo library drives them.
Key specs at a glance
- Weight
- 8.5 to 12 g
- Torque
- About 1.5 to 2.0 kg-cm at 4.8 to 6 V
- Speed
- About 0.10 to 0.12 s/60 degrees
- Supply
- 4.8 to 6 V
- Gears
- ES08A plastic, ES08MA II metal, ES08D/MD digital
- Range
- About 180 degrees with 500 to 2500 us pulses
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1EMAX Servo (More Models)₹1,372
Option 2Emax ES08MA II Metal Gear Micro Servo₹824
What the Emax ES08 micro servo is
These suit small robot arms, RC planes, camera tilt and animatronics where an SG90 is too sloppy. Metal gear versions survive crashes and stalls far better.
Digital versions hold position with more force and draw more current at rest, so size the supply for it. Do not drive past the mechanical end stops; find your servo's safe pulse range first.
Emax ES08 micro servo pinout
The pins on the Emax ES08 micro servo and what each one does.
| Pin | Function |
|---|---|
| Brown / black | Ground |
| Red | Supply, 4.8 to 6 V (see specs) |
| Orange / yellow / white | PWM signal, 50 Hz, 500 to 2500 us pulses |
- Brown / black
- Ground
- Red
- Supply, 4.8 to 6 V (see specs)
- Orange / yellow / white
- PWM signal, 50 Hz, 500 to 2500 us pulses
Wiring the Emax ES08 micro servo
One micro servo can run from the Uno 5V pin for testing, but use a separate 5 V supply for two or more and join the grounds.
| Emax ES08 micro servo pin | Arduino Uno | ESP32 |
|---|---|---|
| Brown (GND) | GND, also to the servo supply ground | GND, also to the servo supply ground |
| Red (V+) | External 5 to 6 V supply (not the 5V pin for big servos) | External 5 to 6 V supply |
| Signal | D9 | GPIO 18 |
- Brown (GND)
- Arduino Uno:
- GND, also to the servo supply ground
- ESP32:
- GND, also to the servo supply ground
- Red (V+)
- Arduino Uno:
- External 5 to 6 V supply (not the 5V pin for big servos)
- ESP32:
- External 5 to 6 V supply
- Signal
- Arduino Uno:
- D9
- ESP32:
- GPIO 18
Example code
If the servo buzzes at the ends, narrow MIN_US and MAX_US.
#include <Servo.h>
Servo s;
const int MIN_US = 600, MAX_US = 2400; // trim to your servo
void setup() { s.attach(9, MIN_US, MAX_US); }
void loop() {
for (int a = 0; a <= 180; a += 2) { s.write(a); delay(15); }
for (int a = 180; a >= 0; a -= 2) { s.write(a); delay(15); }
}Setup and tuning
step the pulse slowly to find where the servo stops moving, then stay inside that range.
use a PCA9685 board and a 5 V supply of at least 1 A per three micro servos.
add a 470 to 1000 uF capacitor across the servo supply.
What you need
Shop this list7 of 8 found in our store · ₹4,203
EMAX Servo (More Models): the part this guide coversEMAX Servo (More Models)₹1,372
Emax ES08MA II Metal Gear Micro Servo: another version this guide coversEmax ES08MA II Metal Gear Micro Servo₹824- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
PCA9685 16-channel PWM / servo driver: to run many servos from two I2C pinsPCA9685 16-Channel PWM / Servo Driver₹1,199
XL4015 5A buck converter with voltmeter: a separate 5 to 6 V supply for the servosXL4015 5A Buck Converter with Voltmeter₹304
RC servo motor tester (3-channel): to centre and test servos without codeRC Servo Motor Tester (3-Channel)₹99
Electrolytic capacitor: bulk capacitance across the supplyElectrolytic Capacitor₹16
Alternatives and when to choose them
- SG90 servo: cheaper, plastic gears.
- MG996R servo: standard size, much more torque.
- PCA9685 servo driver: for many servos.
Common mistakes to avoid
- Driving into the end stops.
- Powering many servos from the board.
- Using thin long wires that drop voltage.
- Mixing digital servo current needs with a weak supply.
Frequently asked questions
Is ES08 better than SG90?
Yes, it has less play and better gears, especially the MA II.
Analog or digital?
Digital holds better and responds faster but uses more current.
Will it work with Servo.h?
Yes.
What horn fits?
The supplied micro horns; the spline is not the same as standard servos.
Can it run on 3.3 V?
No, power it from 4.8 to 6 V; a 3.3 V signal usually works.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

