Component guide · Beginner · 5 min read
ESP8266 Boards and Programming Tools

Wemos D1 R2, D1 Pro Mini and D1 18650, Adafruit Feather HUZZAH, SparkFun Thing Dev, Olimex ESP8266-EVB, ESPresso Lite, ESP8266-DevKitC, Witty Cloud, ACEBOTT QA010, ESP-01 USB Downloader, Burning Fixture and Gravity Wi-Fi Modules
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP8266 is the low-cost Wi-Fi chip that started home-made IoT. Wemos D1 R2 has an Uno layout; D1 Pro Mini adds 16 MB flash and an antenna socket; Feather HUZZAH and SparkFun Thing add LiPo charging; Olimex EVB has a relay; Witty Cloud has an LDR and RGB LED. ESP-01 USB downloaders and burning fixtures program bare ESP-01 or ESP-12 modules.
Key specs at a glance
- Chip
- ESP8266, 80/160 MHz, 2.4 GHz Wi-Fi only (no Bluetooth)
- Flash
- 1-16 MB
- Analog
- One ADC pin, 0-1V on the chip (0-3.3V on most boards with a divider)
- USB-serial
- CH340, CP2102, FT231X or CH9102
- Programming
- Arduino ESP8266 core, MicroPython, ESPHome, Tasmota
- Tools
- ESP-01 USB downloader with auto-reset, pogo-pin burning fixture
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ACEBOTT QA010 ESP8266 Wi-Fi Development Board w/ Type-C₹1,159
Option 2AI-Thinker ESP8266 Cloud Feature Beta Black Board T5₹320
Option 3Adafruit Feather HUZZAH ESP8266 WiFi Development Board₹2,109
Option 4ESPresso Lite V2.0 ESP8266 WROOM-02 IoT Wi-Fi Dev Board₹892
Option 5ESP8266 Adapter Plate Serial Wireless Wi-Fi Module₹44
Option 6ESP8266 Burning Fixture Tool Downloader Programming Board₹536
What the ESP8266 boards and programming tools (Wemos D1, HUZZAH, Thing, Olimex EVB, Witty Cloud, ESP-01 programmers) is
ESP8266 boards such as the NodeMCU, Wemos D1 Mini and ESP-01, plus USB adapters and programmers, give cheap 2.4 GHz Wi-Fi with a single-core 80 MHz chip.
For new projects an ESP32-C3 costs about the same and adds Bluetooth, but the ESP8266 is still fine for simple Wi-Fi sensors, relays and Tasmota or ESPHome devices.
ESP-01 modules need 3.3V at up to 300 mA during Wi-Fi bursts; an Arduino's 3.3V pin is too weak. The USB downloader with CH9102F and auto-download circuit flashes ESP-01 and ESP-01S without pressing buttons.
ESP8266 boards and programming tools (Wemos D1, HUZZAH, Thing, Olimex EVB, Witty Cloud, ESP-01 programmers) pinout
The pins on the ESP8266 boards and programming tools (Wemos D1, HUZZAH, Thing, Olimex EVB, Witty Cloud, ESP-01 programmers) and what each one does.
| Pin | Function |
|---|---|
| USB | Power, flashing and serial (CP2102, CH340, CH9102 or native USB) |
| EN / RST | Reset |
| BOOT / GPIO0 | Hold low to enter the bootloader |
| 3V3 / GND | 3.3V supply out |
| GPIO | 3.3V logic only |
- USB
- Power, flashing and serial (CP2102, CH340, CH9102 or native USB)
- EN / RST
- Reset
- BOOT / GPIO0
- Hold low to enter the bootloader
- 3V3 / GND
- 3.3V supply out
- GPIO
- 3.3V logic only
Wiring the ESP8266 boards and programming tools (Wemos D1, HUZZAH, Thing, Olimex EVB, Witty Cloud, ESP-01 programmers)
ESP GPIO is 3.3V. Avoid boot strapping pins (GPIO0, 2, 12, 15 on ESP32; GPIO0, 2, 15 on ESP8266) for inputs that may be pulled at power-up.
| ESP8266 boards and programming tools (Wemos D1, HUZZAH, Thing, Olimex EVB, Witty Cloud, ESP-01 programmers) pin | Connection | Note |
|---|---|---|
| USB | To PC | Install the USB-serial driver if needed |
| Sensors | I2C or SPI pins | 3.3V logic |
| Battery | JST LiPo on Feather-style boards | 1S only |
- USB
- Connection:
- To PC
- Note:
- Install the USB-serial driver if needed
- Sensors
- Connection:
- I2C or SPI pins
- Note:
- 3.3V logic
- Battery
- Connection:
- JST LiPo on Feather-style boards
- Note:
- 1S only
Example code
The built-in LED on most ESP8266 boards is active low. Open http://<ip>/on in a browser on the same network.
#include <ESP8266WiFi.h>
#include <ESP8266WebServer.h>
ESP8266WebServer server(80);
void setup() {
pinMode(LED_BUILTIN, OUTPUT);
WiFi.begin("YOUR_WIFI", "YOUR_PASSWORD");
while (WiFi.status() != WL_CONNECTED) delay(300);
Serial.begin(115200);
Serial.println(WiFi.localIP());
server.on("/on", [] { digitalWrite(LED_BUILTIN, LOW); server.send(200, "text/plain", "on"); });
server.on("/off", [] { digitalWrite(LED_BUILTIN, HIGH); server.send(200, "text/plain", "off"); });
server.begin();
}
void loop() { server.handleClient(); }Setup and tuning
add the ESP8266 core URL in the Arduino IDE and pick NodeMCU 1.0 or LOLIN D1 Mini.
install the CH340 or CP2102 driver if no port shows up.
use an ESP-01 USB adapter with a flash switch, or tie GPIO0 to GND during reset to flash.
use D-pin names on NodeMCU; avoid D3, D4 and D8 for inputs because they affect boot.
A0 reads 0 to 1 V on the bare chip and 0 to 3.3 V on boards with a divider.
What you need
Shop this list20 of 20 found in our store · ₹15,311
ACEBOTT QA010 ESP8266 Wi-Fi Development Board w/ Type-C: the part this guide coversACEBOTT QA010 ESP8266 Wi-Fi Development Board w/ Type-C₹1,159
AI-Thinker ESP8266 Cloud Feature Beta Black Board T5: another version this guide coversAI-Thinker ESP8266 Cloud Feature Beta Black Board T5₹320
Adafruit Feather HUZZAH ESP8266 WiFi Development Board: another version this guide coversAdafruit Feather HUZZAH ESP8266 WiFi Development Board₹2,109
ESPresso Lite V2.0 ESP8266 WROOM-02 IoT Wi-Fi Dev Board: another version this guide coversESPresso Lite V2.0 ESP8266 WROOM-02 IoT Wi-Fi Dev Board₹892
ESP8266 Adapter Plate Serial Wireless Wi-Fi Module: another version this guide coversESP8266 Adapter Plate Serial Wireless Wi-Fi Module₹44
ESP8266 Burning Fixture Tool Downloader Programming Board: another version this guide coversESP8266 Burning Fixture Tool Downloader Programming Board₹536
ESP8266 ESP-01/01S USB Downloader w/ CH9102F & Auto-Download Circuit: another version this guide coversESP8266 ESP-01/01S USB Downloader w/ CH9102F & Auto-Download Circuit₹219
ESP8266 ESP-01/ESP-01S DHT11 Temperature Humidity WiFi Node: another version this guide coversESP8266 ESP-01/ESP-01S DHT11 Temperature Humidity WiFi Node₹106
Espressif ESP8266-DevKitC Development Board w/ ESP-WROOM-02D: another version this guide coversEspressif ESP8266-DevKitC Development Board w/ ESP-WROOM-02D₹559
Olimex ESP8266-EVB Evaluation Board w/ Relay & UEXT: another version this guide coversOlimex ESP8266-EVB Evaluation Board w/ Relay & UEXT₹1,459
Olimex ESP8266-EVB-BAT Wi-Fi Development Board w/ Relay & LiPo Charger: another version this guide coversOlimex ESP8266-EVB-BAT Wi-Fi Development Board w/ Relay & LiPo Charger₹1,879
SparkFun ESP8266 Thing Dev Board w/ FTDI USB-to-Serial: another version this guide coversSparkFun ESP8266 Thing Dev Board w/ FTDI USB-to-Serial₹1,219
Wemos D1 ESP-WROOM-02 ESP8266 Mini WiFi NodeMCU Module w/ 18650 Battery: another version this guide coversWemos D1 ESP-WROOM-02 ESP8266 Mini WiFi NodeMCU Module w/ 18650 Battery₹469
Wemos ESP8266 D1 Pro Mini 16MB External Antenna Connector: another version this guide coversWemos ESP8266 D1 Pro Mini 16MB External Antenna Connector₹719
Wemos ESP8266 D1 R2 V2.1.0 WiFi Development Board: another version this guide coversWemos ESP8266 D1 R2 V2.1.0 WiFi Development Board₹287
Wireless-Tag WT8266-S5 ESP8266 Wi-Fi Module: another version this guide coversWireless-Tag WT8266-S5 ESP8266 Wi-Fi Module₹339
Witty Cloud ESP8266 ESP-12F Development Board w/ LDR & RGB LED: another version this guide coversWitty Cloud ESP8266 ESP-12F Development Board w/ LDR & RGB LED₹249
Elecrow Crowtail Serial WiFi Module w/ UART Interface: another version this guide coversElecrow Crowtail Serial WiFi Module w/ UART Interface₹529
DFRobot Gravity WiFi IoT Module for SCI DAQ: another version this guide coversDFRobot Gravity WiFi IoT Module for SCI DAQ₹549
DFRobot Gravity WiFi IoT Module w/ I2C & UART: another version this guide coversDFRobot Gravity WiFi IoT Module w/ I2C & UART₹1,669
Alternatives and when to choose them
- NodeMCU ESP8266: the most common board.
- ESP-01: the tiny module.
- ESP32 vs ESP8266: which to choose.
Common mistakes to avoid
- Using a charge-only USB cable.
- Powering an ESP-01 from an Uno's 3.3 V pin, which cannot supply enough current.
- Putting inputs on boot-strapping pins.
- Feeding 3.3 V into A0 on a bare chip that reads only 1 V.
Frequently asked questions
Why is no COM port shown for my NodeMCU?
Install the CH340 or CP2102 driver and use a data USB cable.
How do I flash an ESP-01?
Use an adapter with a program switch, or tie GPIO0 to GND while it resets.
Can the ESP8266 read 5 V signals?
No. Its pins are 3.3 V; use a divider or level shifter.
Why does my board not boot with a sensor attached?
The sensor pulls a boot pin (D3, D4 or D8) the wrong way at startup.
Should I choose ESP8266 or ESP32?
ESP8266 is fine for simple Wi-Fi jobs; ESP32 has more pins, Bluetooth and power.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


