Component guide · Beginner · 3 min read
GSR Galvanic Skin Response Sensors

Seeed Studio Grove GSR Sensor v1.2 with Finger Straps and CJMCU-6701 Skin Conductance Module
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A GSR sensor measures how easily a tiny current flows across your skin. Sweat glands react to excitement, stress and surprise, so the reading rises and falls with emotional arousal. Two finger straps or pads connect to the module, which gives an analog voltage to an Arduino or ESP32. It is used for biofeedback games, relaxation trainers and psychology class experiments, not for lie detection or medical diagnosis.
Key specs at a glance
- Measures
- Skin conductance (electrodermal activity)
- Output
- Analog voltage
- Supply
- 3.3V to 5V
- Electrodes
- Two finger straps (Grove) or pads
- Response
- Changes over 1 to 5 seconds
- Use
- Education and biofeedback, not medical
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the GSR galvanic skin response sensors: Grove GSR v1.2 and CJMCU-6701 is
GSR (galvanic skin response) sensors measure tiny changes in skin conductance from sweat, used for stress, emotion and biofeedback projects.
Strap the electrodes on two fingers of the same hand and sit still for a minute so the reading settles. Then watch the trend, not the absolute number: a sudden rise a second or two after a surprise is the classic GSR response.
Readings differ a lot between people and with room temperature and dry or damp skin, so compare each person against their own baseline. Keep the person on battery power or a laptop on battery when the sensor is attached, never a mains-powered circuit without isolation.
GSR galvanic skin response sensors: Grove GSR v1.2 and CJMCU-6701 pinout
The pins on the GSR galvanic skin response sensors: Grove GSR v1.2 and CJMCU-6701 and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3V or 5V |
| GND | Ground |
| SIG | Analog output |
| Finger electrodes | Two straps on one hand |
- VCC
- 3.3V or 5V
- GND
- Ground
- SIG
- Analog output
- Finger electrodes
- Two straps on one hand
Wiring the GSR galvanic skin response sensors: Grove GSR v1.2 and CJMCU-6701
Use battery or laptop-on-battery power while the sensor is on a person.
| GSR galvanic skin response sensors: Grove GSR v1.2 and CJMCU-6701 pin | Arduino | Note |
|---|---|---|
| VCC | 5V | |
| GND | GND | |
| SIG | A0 | Grove analog port |
- VCC
- Arduino:
- 5V
- GND
- Arduino:
- GND
- SIG
- Arduino:
- A0
- Note:
- Grove analog port
Example code
On the Grove module a higher reading means lower skin conductance; check your module's notes and flip the scale if needed.
const int GSR = A0;
void setup() {
Serial.begin(9600);
}
void loop() {
long sum = 0;
for (int i = 0; i < 10; i++) { // average 10 readings
sum += analogRead(GSR);
delay(5);
}
int gsr = sum / 10;
Serial.println(gsr); // open Serial Plotter to see the trend
delay(100);
}Setup and tuning
wear the finger electrodes on two fingers with firm, even contact.
connect the module output to an analog pin, 5 V and GND.
sample several times per second and smooth with a moving average.
record a calm baseline for a minute before measuring changes.
it is for hobby and research use, not medical diagnosis.
What you need
Shop this list2 of 2 found in our store · ₹1,981
Seeed Studio Studio Grove GSR Sensor v1.2 – Galvanic Skin Response Module w/ Finger Straps: the part this guide coversSeeed Studio Grove GSR Sensor v1.2 – Galvanic Skin Response Module w/ Finger Straps₹1,109
CJMCU-6701 GSR Skin Sensor Module: another version this guide coversCJMCU-6701 GSR Skin Sensor Module₹872
Alternatives and when to choose them
- ECG, EMG and biopotential sensors: heart and muscle signals.
- MAX30102 heart rate sensor: pulse and SpO2.
- ADC basics: reading analog sensors.
Common mistakes to avoid
- Using loose electrodes.
- Treating results as medical data.
- Skipping the baseline.
- Reading raw values without smoothing.
Frequently asked questions
What does a GSR sensor measure?
Changes in skin conductance caused by sweat gland activity.
Can it detect lies or stress accurately?
No. It shows arousal changes, but many things affect it.
Why do readings drift?
Skin moisture and temperature change; record a baseline and look at changes.
Is the sensor safe to wear?
Yes. It passes a tiny current, but do not use it on broken skin.
Which Arduino pin should I use?
Any analog input, such as A0, sampled several times per second.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
