Component guide · Beginner · 3 min read
MG945, MG946R, MG958 and Power HD 1501MG Metal Gear Servos

Specs and Wiring
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MG945, MG946R, MG958 and Power HD 1501MG are standard-size servos with metal gears and 10 to 20 kg-cm of torque. They are used in robot arms, legged robots and RC steering where plastic gears would strip. They take the usual 50 Hz PWM signal, but stall current reaches 2 to 3 A, so the power supply matters more than the code.
Key specs at a glance
- Torque
- MG945 about 11, MG946R about 13, MG958 about 18, 1501MG about 17 kg-cm at 6 V
- Speed
- About 0.14 to 0.20 s/60 degrees
- Supply
- 4.8 to 6 V (MG958 up to 7.2 V)
- Stall current
- About 1.5 to 3 A each
- Gears
- Metal, ball bearing output
- Spline
- 25T on most (fits the 25T metal horn)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1TowerPro MG945 Metal Gear Servo₹420
Option 2MG958 Metal Gear Digital Servo₹1,095
Option 3Standard Metal Gear Servo MG946R₹756
Option 4Power HD 1501MG Metal Gear Servo₹1,302
What the MG945 and MG958 metal gear servo is
MG958 is digital and fast; MG945 and MG946R are analog; the Power HD 1501MG is a well-made analog servo popular in hexapods and arms.
For a 4 to 6 joint arm, budget at least 2 A per moving servo and use a 5 to 6 V supply rated 6 to 10 A. Brownouts from a weak supply reset the controller and make servos twitch.
MG945 and MG958 metal gear servo pinout
The pins on the MG945 and MG958 metal gear servo and what each one does.
| Pin | Function |
|---|---|
| Brown / black | Ground |
| Red | Supply, 4.8 to 6 V (see specs) |
| Orange / yellow / white | PWM signal, 50 Hz, 500 to 2500 us pulses |
- Brown / black
- Ground
- Red
- Supply, 4.8 to 6 V (see specs)
- Orange / yellow / white
- PWM signal, 50 Hz, 500 to 2500 us pulses
Wiring the MG945 and MG958 metal gear servo
Use thick wires from the supply to a servo power rail, a 1000 uF capacitor on that rail, and a common ground with the controller.
| MG945 and MG958 metal gear servo pin | Arduino Uno | ESP32 |
|---|---|---|
| Brown (GND) | GND, also to the servo supply ground | GND, also to the servo supply ground |
| Red (V+) | External 5 to 6 V supply (not the 5V pin for big servos) | External 5 to 6 V supply |
| Signal | D9 | GPIO 18 |
- Brown (GND)
- Arduino Uno:
- GND, also to the servo supply ground
- ESP32:
- GND, also to the servo supply ground
- Red (V+)
- Arduino Uno:
- External 5 to 6 V supply (not the 5V pin for big servos)
- ESP32:
- External 5 to 6 V supply
- Signal
- Arduino Uno:
- D9
- ESP32:
- GPIO 18
Example code
Ramping the angle avoids current spikes and jerky arms.
#include <Servo.h>
Servo s;
int pos = 90;
void moveTo(int target) {
while (pos != target) {
pos += (target > pos) ? 1 : -1;
s.write(pos);
delay(10); // slower = less current spike
}
}
void setup() { s.attach(9); s.write(pos); }
void loop() { moveTo(30); delay(800); moveTo(150); delay(800); }Setup and tuning
a 6 V 10 A SMPS or a 2S pack with a 6 V UBEC suits multi-servo arms.
use metal 25T horns; plastic horns slip under load.
servos holding a load against gravity warm up; add counterweights or springs.
What you need
Shop this list9 of 10 found in our store · ₹5,461
TowerPro MG945 Metal Gear Servo: the part this guide coversTowerPro MG945 Metal Gear Servo₹420
MG958 Metal Gear Digital Servo: another version this guide coversMG958 Metal Gear Digital Servo₹1,095
Standard Metal Gear Servo MG946R: another version this guide coversStandard Metal Gear Servo MG946R₹756
Power HD 1501MG Metal Gear Servo: another version this guide coversPower HD 1501MG Metal Gear Servo₹1,302- Uno R3 development board: the controller used in the wiring tableFind this part
PCA9685 16-channel PWM / servo driver: to run many servos from two I2C pinsPCA9685 16-Channel PWM / Servo Driver₹1,199
SMPS power supply in metal enclosure (5/12/24 V): a bench supply for servo projectsSMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
XL4015 5A buck converter with voltmeter: a separate 5 to 6 V supply for the servosXL4015 5A Buck Converter with Voltmeter₹304
Metal servo horn 25T: a stronger horn for 25-tooth spline servosMetal Servo Horn 25T (for MG995 / MG996R)₹71Closest match, check the specs
Electrolytic capacitor: bulk capacitance across the supplyElectrolytic Capacitor₹16
Alternatives and when to choose them
- MG996R servo: the common budget choice.
- DS3218 servo: 20 kg-cm digital with a bracket.
- Serial bus servos: position feedback and daisy-chain wiring.
Common mistakes to avoid
- Underpowering several servos.
- Using plastic horns on heavy joints.
- Moving at full speed and causing resets.
- Running 7.4 V into 6 V servos.
Frequently asked questions
Which is strongest?
MG958 and 1501MG, around 17 to 18 kg-cm.
Do they fit MG996R brackets?
Yes, they are the same standard size.
Analog or digital?
MG958 is digital; MG945, MG946R and 1501MG are analog.
Can PCA9685 drive them?
Yes, signal only; power them separately.
Why does my Arduino reset?
Servo current spikes pull the supply down; separate the supplies.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

