Component guide · Beginner · 3 min read
Mini Air and Vacuum Pumps (310, Mitsumi, Kamoer KVP8 Plus)

Wiring and Uses
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Mini air pumps are diaphragm pumps that blow air from one port and suck from the other. Used as vacuum pumps they hold suction cups for pick-and-place grippers, and as air pumps they inflate cuffs or aerate tanks. The 310 and Mitsumi pumps are brushed and low cost; the Kamoer KVP8 Plus is brushless for long, quiet running.
Key specs at a glance
- Voltage
- 3 to 6 V (Mitsumi), 6 to 12 V (310), 12 V (KVP8 Plus)
- Current
- About 100 to 500 mA
- Vacuum
- About -40 to -65 kPa
- Flow
- About 0.5 to 3 L/min
- Motor
- Brushed or brushless (Kamoer)
- Ports
- Inlet and outlet barbs
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1310 Mini Vacuum / Air Pump 6V-12V₹89
Option 2Mitsumi Micro Air Pump₹649
Option 3Kamoer KVP8 Plus 12V Brushless Vacuum Pump₹2,800
What the Mini air and vacuum pump is
A mini air pump is a small diaphragm pump that pushes air out of one port and sucks air in at the other. Used on the suction side it becomes a vacuum pump for grippers.
For a vacuum gripper, connect the pump inlet to the suction cup and add a small solenoid valve to release the part quickly. Without a release valve, the part drops slowly as air leaks back.
Mini air and vacuum pump pinout
The pins on the Mini air and vacuum pump and what each one does.
| Pin | Function |
|---|---|
| + | Motor lead |
| - | Motor lead |
- +
- Motor lead
- -
- Motor lead
Wiring the Mini air and vacuum pump
Add a diode across brushed pumps. Use separate channels for the pump and release valve.
| Mini air and vacuum pump pin | Arduino Uno | ESP32 |
|---|---|---|
| Load + | 12 V supply + | 12 V supply + |
| Load - | MOSFET module OUT- (or relay NO) | MOSFET module OUT- |
| Module signal | D7 | GPIO 26 |
| GND | GND (shared with 12 V -) | GND |
- Load +
- Arduino Uno:
- 12 V supply +
- ESP32:
- 12 V supply +
- Load -
- Arduino Uno:
- MOSFET module OUT- (or relay NO)
- ESP32:
- MOSFET module OUT-
- Module signal
- Arduino Uno:
- D7
- ESP32:
- GPIO 26
- GND
- Arduino Uno:
- GND (shared with 12 V -)
- ESP32:
- GND
Example code
A minimal sketch to check the part works.
const int PUMP = 7, VALVE = 8;
void setup() { pinMode(PUMP, OUTPUT); pinMode(VALVE, OUTPUT); }
void loop() {
digitalWrite(VALVE, LOW); digitalWrite(PUMP, HIGH); // grip
delay(3000);
digitalWrite(PUMP, LOW); digitalWrite(VALVE, HIGH); // release
delay(500);
digitalWrite(VALVE, LOW);
delay(3000);
}Setup and tuning
connect the pump inlet to the suction cup and add a small solenoid valve to vent the line so parts release at once.
keep it short and tight on the barbs; leaks and long tubes weaken suction.
match the suction cup to the part; larger cups lift more on flat surfaces.
drive brushed pumps with a MOSFET module and a flyback diode.
mount on foam to reduce hum.
What you need
Shop this list6 of 8 found in our store · ₹31,502
310 Mini Vacuum / Air Pump 6V-12V: the part this guide covers310 Mini Vacuum / Air Pump 6V-12V₹89Closest match, check the specs
Mitsumi Micro Air Pump: another version this guide coversMitsumi Micro Air Pump₹649
Kamoer KVP8 Plus 12V Brushless Vacuum Pump: another version this guide coversKamoer KVP8 Plus 12V Brushless Vacuum Pump₹2,800- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
MOSFET switch module (D4184 / LR7843): to switch or PWM it from a GPIOMOSFET Switch Module, Relay Replacement (D4184 / LR7843)₹39- 1N4007 diode: flyback protection across the coil or motorFind this part
Silicone pump tube (1 m): tubing for the pumpSilicone Pump Tube (1 m)₹35
Alternatives and when to choose them
- Solenoid valves: release valve options.
- Water pumps overview.
Common mistakes to avoid
- Trying to pump water through an air pump.
- Building a gripper without a release valve, so parts drop slowly.
- Using long, loose tubing that leaks.
- Switching it with no flyback diode.
Frequently asked questions
Can a mini air pump pump water?
No. It is built for air only; water damages the valves and motor.
Can I build a vacuum gripper with it?
Yes. Connect a suction cup to the inlet and add a release valve to drop parts quickly.
Which mini pump is brushless?
The Kamoer KVP8 Plus is brushless, so it runs quietly and for much longer than brushed pumps.
Can I control the pump speed?
Brushed pumps slow down with PWM through a MOSFET. Brushless pumps need a version that supports speed control.
Can it aerate an aquarium?
Yes. Used as an air pump it can feed an air stone in a small tank.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


