Component guide · Beginner · 3 min read
MPU6500 (GY-6500, GY-91, GY-9255), ICM-20602, ICM-20689, MPU6886

and ICG-20660L 6-Axis IMUs
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These InvenSense 6-axis IMUs are close relatives of the MPU6050 and share its register map for accelerometer and gyro data. The MPU6500 runs at 3.3 V with SPI; the GY-91 adds a BMP280 barometer; the GY-9255 is an MPU9255 board without a working magnetometer. The ICM-20602 and ICM-20689 are flight-controller grades, and the MPU6886 is used in M5Stack.
Key specs at a glance
- Sensors
- 3-axis accelerometer and 3-axis gyroscope
- Ranges
- ±2 to ±16 g; ±250 to ±2000 °/s
- Interface
- I2C (0x68 or 0x69) and SPI
- Supply
- Modules 3.3 to 5 V; chips 1.7 to 3.45 V
- WHO_AM_I
- 0x70 MPU6500, 0x12 ICM-20602, 0x98 ICM-20689, 0x19 MPU6886
- Extras
- BMP280 barometer on GY-91
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1MPU6500 GY-6500 6-Axis Accelerometer Gyro Module – I2C/SPI Interface₹314
Option 2MPU6500 6-Axis Gyro Accelerometer DMP Motion Sensor Module – I2C/SPI₹159
Option 3TDK InvenSense MPU-6500 QFN-24 6-Axis Accelerometer Gyro – I2C/SPI Interface₹589
Option 4GY-91 MPU6500 + BMP280 7DOF IMU Sensor Module – I2C/SPI Interface₹605
Option 5GY-9255 MPU9255 Sensor Module (without Magnetometer) – 6-Axis IMU, I2C Interface₹579
Option 6TDK InvenSense ICM-20602 LGA-16 6-Axis Accelerometer Gyro Sensor₹1,067
What the MPU6500, ICM-20602, ICM-20689 and MPU6886 IMUs is
The TDK MPU-6500 and ICM-20602 are 6-axis IMUs with a 3-axis gyro and accelerometer, used in flight controllers, robots and wearables.
Because the data registers match the MPU6050, simple register code works on all of them. Libraries that check WHO_AM_I may refuse a chip they do not expect, which is the most common reason a sketch says 'not found'.
Fake MPU9250 boards are often MPU6500 inside; read WHO_AM_I to know what you have.
MPU6500, ICM-20602, ICM-20689 and MPU6886 IMUs pinout
The pins on the MPU6500, ICM-20602, ICM-20689 and MPU6886 IMUs and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| SCL / SDA | I2C |
| AD0 / SDO | Address select or SPI MISO |
| NCS | SPI chip select |
| INT | Interrupt |
- VCC
- Supply
- GND
- Ground
- SCL / SDA
- I2C
- AD0 / SDO
- Address select or SPI MISO
- NCS
- SPI chip select
- INT
- Interrupt
Wiring the MPU6500, ICM-20602, ICM-20689 and MPU6886 IMUs
Modules with a regulator run from 3.3 V or 5 V. Bare chips (LGA or QFN parts) are 1.8 to 3.6 V only: mount them on a breakout and use a level shifter with 5 V boards.
| MPU6500, ICM-20602, ICM-20689 and MPU6886 IMUs pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
Prints WHO_AM_I first so you can see which chip is on your board.
// Read raw accel and gyro from an MPU6500-family IMU (same registers as MPU6050)
#include <Wire.h>
const uint8_t ADDR = 0x68;
int16_t rd16() { return (Wire.read() << 8) | Wire.read(); }
void setup() {
Serial.begin(115200);
Wire.begin();
Wire.beginTransmission(ADDR); Wire.write(0x75); Wire.endTransmission(false);
Wire.requestFrom(ADDR, (uint8_t)1);
Serial.print("WHO_AM_I = 0x"); Serial.println(Wire.read(), HEX);
Wire.beginTransmission(ADDR); Wire.write(0x6B); Wire.write(0); Wire.endTransmission(); // wake up
}
void loop() {
Wire.beginTransmission(ADDR); Wire.write(0x3B); Wire.endTransmission(false);
Wire.requestFrom(ADDR, (uint8_t)14);
float ax = rd16() / 16384.0, ay = rd16() / 16384.0, az = rd16() / 16384.0; // +-2 g
rd16(); // temperature
float gx = rd16() / 131.0, gy = rd16() / 131.0, gz = rd16() / 131.0; // +-250 dps
Serial.printf("acc g %.2f %.2f %.2f gyro dps %.1f %.1f %.1f\n", ax, ay, az, gx, gy, gz);
delay(100);
}Setup and tuning
VCC 3.3 V, GND, and I2C or SPI.
use an MPU6500 or MPU9250-style library (without the magnetometer).
use SPI for fast control loops.
keep still at start-up to measure gyro bias.
soft-mount away from motors.
What you need
Shop this list12 of 13 found in our store · ₹10,517
Generic MPU6500 GY-6500 6-Axis Accelerometer Gyro Module – I2C/SPI Interface: the part this guide coversMPU6500 GY-6500 6-Axis Accelerometer Gyro Module – I2C/SPI Interface₹314
Generic MPU6500 6-Axis Gyro Accelerometer DMP Motion Sensor Module – I2C/SPI: another version this guide coversMPU6500 6-Axis Gyro Accelerometer DMP Motion Sensor Module – I2C/SPI₹159
TDK TDK InvenSense MPU-6500 QFN-24 6-Axis Accelerometer Gyro – I2C/SPI Interface: another version this guide coversTDK InvenSense MPU-6500 QFN-24 6-Axis Accelerometer Gyro – I2C/SPI Interface₹589
Generic GY-91 MPU6500 + BMP280 7DOF IMU Sensor Module – I2C/SPI Interface: another version this guide coversGY-91 MPU6500 + BMP280 7DOF IMU Sensor Module – I2C/SPI Interface₹605
Generic GY-9255 MPU9255 Sensor Module (without Magnetometer) – 6-Axis IMU, I2C Interface: another version this guide coversGY-9255 MPU9255 Sensor Module (without Magnetometer) – 6-Axis IMU, I2C Interface₹579
TDK TDK InvenSense ICM-20602 LGA-16 6-Axis Accelerometer Gyro Sensor: another version this guide coversTDK InvenSense ICM-20602 LGA-16 6-Axis Accelerometer Gyro Sensor₹1,067
TDK InvenSense ICM-20689 6-Axis MEMS IMU Motion Sensor Module – I2C/SPI Interface: another version this guide coversTDK InvenSense ICM-20689 6-Axis MEMS IMU Motion Sensor Module – I2C/SPI Interface₹679
M5Stack MPU6886 6-Axis IMU Unit – I2C Interface, 2x LEGO Holes: another version this guide coversM5Stack MPU6886 6-Axis IMU Unit – I2C Interface, 2x LEGO Holes₹979
DFRobot Fermion ICG20660L 6-Axis IMU Module (Breakout) – I2C/SPI Interface: another version this guide coversDFRobot Fermion ICG20660L 6-Axis IMU Module (Breakout) – I2C/SPI Interface₹2,619
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
GY-521 MPU6050 6-axis module: the classic low-cost IMUGY-521 MPU6050 6-Axis Gyro and Accelerometer Module₹169Closest match, check the specs
MPU9250 9-axis module: a 9-axis InvenSense moduleMPU9250 9-Axis Gyro Accelerometer Magnetometer Sensor Module with I2C Interface₹2,369
Alternatives and when to choose them
- MPU6050: the 5 V-friendly original.
- MPU9250: adds a magnetometer.
- ICM-42688-P: lower noise successor.
Common mistakes to avoid
- Using 5 V logic.
- Moving during calibration.
- Mounting near motors.
- Expecting a magnetometer.
Frequently asked questions
What is the difference between MPU-6500 and MPU-6050?
The MPU-6500 is newer, supports SPI and has lower noise.
Does the ICM-20602 have a magnetometer?
No. It is a 6-axis IMU, so add a separate magnetometer for heading.
Why does my gyro drift?
The gyro bias was not measured at start-up; keep it still while it calibrates.
Should I use SPI or I2C?
Use SPI for fast control loops like flight controllers, and I2C for simple projects.
Is it 5 V tolerant?
No. The chip runs at 3.3 V, so use level shifting with 5 V boards.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

