Component guide · Beginner · 3 min read
NEMA 8 (20 mm) Hybrid Stepper Motor

Specs, Wiring and Driver Choice
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A NEMA 8 stepper is a 20 mm square hybrid stepper with 200 steps per turn. It is small and light, made for micro positioning stages, small camera sliders, syringe pumps and focus drives. Its coils take only a few hundred milliamps, so set the driver current low, and expect a few newton-centimetres of torque.
Key specs at a glance
- Frame
- 20 x 20 mm
- Step angle
- 1.8 degrees (200 steps/rev)
- Current
- About 0.5 to 0.6 A per phase
- Holding torque
- About 1.5 to 3 N-cm
- Wires
- 4, bipolar
- Shaft
- 4 mm
What the NEMA 8 stepper motor is
A NEMA 8 stepper is the smallest common hybrid stepper size, with a 20 mm square face. Like larger steppers it moves in 1.8 degree steps, but with much lower current and torque.
Small steppers lose steps easily if accelerated too fast; use AccelStepper with gentle acceleration. Set driver current to the rated value or slightly below to avoid overheating.
NEMA 8 stepper motor pinout
The pins on the NEMA 8 stepper motor and what each one does.
| Pin | Function |
|---|---|
| A+ / A- | Coil A |
| B+ / B- | Coil B |
- A+ / A-
- Coil A
- B+ / B-
- Coil B
Wiring the NEMA 8 stepper motor
Find coil pairs with a multimeter: a pair reads a few ohms, different pairs read open.
| NEMA 8 stepper motor pin | DRV8825 / A4988 | TMC2209 |
|---|---|---|
| Coil A | Driver 1A / 1B | Driver 1A / 1B |
| Coil B | Driver 2A / 2B | Driver 2A / 2B |
- Coil A
- DRV8825 / A4988:
- Driver 1A / 1B
- TMC2209:
- Driver 1A / 1B
- Coil B
- DRV8825 / A4988:
- Driver 2A / 2B
- TMC2209:
- Driver 2A / 2B
Example code
A minimal sketch to check the part works.
#include <AccelStepper.h>
AccelStepper st(AccelStepper::DRIVER, 3, 2);
void setup() { st.setMaxSpeed(800); st.setAcceleration(400); }
void loop() {
if (st.distanceToGo() == 0) st.moveTo(-st.currentPosition() + 400);
st.run();
}Setup and tuning
set the driver (A4988, DRV8825 or TMC2208) to about 0.5 A or slightly below the motor's label.
12 V through a current-limiting driver is enough; higher voltage helps at speed.
use AccelStepper with gentle acceleration; small motors lose steps easily.
M2 screws on 16 mm hole spacing; do not let screws touch the windings inside.
use a 4 mm bore coupler or pulley sized for the shaft.
What you need
Shop this list3 of 4 found in our store · ₹2,389
NEMA8 (20mm) Hybrid Stepper Motor: the part this guide coversNEMA8 (20mm) Hybrid Stepper Motor₹1,999- Uno R3 development board: the controller used in the wiring tableFind this part
DRV8825 stepper driver with heatsink: a StepStick driver for small steppersDRV8825 Stepper Motor Driver with Heatsink₹92Closest match, check the specs
SMPS power supply in metal enclosure (5/12/24 V): a 12 or 24 V supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
Alternatives and when to choose them
Common mistakes to avoid
- Setting the driver current too high, which overheats the small motor.
- Using fast acceleration, so the motor skips steps.
- Pairing the wrong wires as a coil.
- Expecting NEMA 17 torque from a NEMA 8.
Frequently asked questions
Which driver should I use for a NEMA 8 stepper?
Any StepStick driver such as an A4988, DRV8825 or TMC2208, set to a low current around 0.5 A.
How much torque does a NEMA 8 give?
About 1.5 to 3 N·cm of holding torque, enough for small stages, sliders and pumps but not for heavy loads.
What voltage does it run on?
Run it from 12 V through a current-limiting driver. The driver keeps coil current at the setting even though the supply is higher than the coil rating.
Can I use a ULN2003 board?
No. The ULN2003 drives unipolar motors; a 4-wire NEMA 8 is bipolar and needs an H-bridge driver.
What is a NEMA 8 used for?
Micro positioning stages, camera focus drives, syringe pumps and small camera sliders.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

