Component guide · Beginner · 4 min read
NTC Thermistor Probes (B3950 10k and 100k, Stainless, Pipe, Ring Terminal, BMS)

Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An NTC thermistor probe is a resistor that drops in value as it warms, sealed in a steel tube, plastic overmould or ring terminal. The 10k B3950 type is common for water, air and pipes, the 100k B3950 for 3D printers and hot plates. Read one with a fixed resistor divider and the beta formula on any analog pin.
Key specs at a glance
- Resistance at 25 degrees C
- 10 k or 100 k (also 5 k on some appliance sensors)
- Beta value
- 3950 K typical (check the label, e.g. 3977)
- Tolerance
- 1% on most probes
- Range
- About -30 to 105 degrees C (cable), to 250 degrees C on glass 100k
- Housing
- Stainless tube, TPE overmould, ring terminal, clip or bullet
- Connector
- Bare leads, XH2.54 or 2-pin terminal
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 5 Meter Cable₹98
Option 2B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 4 Meter Cable₹108
Option 3B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with 2Meter Cable & XH2.54 Connector₹77
Option 4B3950 10K NTC Thermistor Temperature Sensor 5x20mm Stainless Steel Probe w/ 0.5m Cable & XH2.54 Connector₹46
Option 5B3950 100K NTC Thermistor Temperature Sensor 3x20mm Stainless Steel Probe w/ 1m Cable & XH2.54 Connector₹63
Option 6B3950 100K NTC Thermistor Temperature Sensor 3x25mm with XH2.54 Connector & 1 Meter Cable₹64
What the NTC thermistor probes (B3950 10k and 100k) is
NTC thermistor probes are waterproof temperature sensors in steel tubes or epoxy heads, used for tanks, fridges, 3D printers and HVAC.
Use a fixed resistor equal to the probe's 25 degrees C value. That puts the middle of the range near half the ADC, where resolution is best.
The beta formula is accurate to about 1 degree C over a 50 degree span. For wider ranges use the Steinhart-Hart equation with three calibration points.
NTC thermistor probes (B3950 10k and 100k) pinout
The pins on the NTC thermistor probes (B3950 10k and 100k) and what each one does.
| Pin | Function |
|---|---|
| Lead 1 | Analog pin and fixed resistor |
| Lead 2 | GND |
- Lead 1
- Analog pin and fixed resistor
- Lead 2
- GND
Wiring the NTC thermistor probes (B3950 10k and 100k)
The ESP32 ADC is not linear near its ends. Average many samples or use an external ADC for better than 1 degree C.
| NTC thermistor probes (B3950 10k and 100k) pin | Arduino Uno | ESP32 |
|---|---|---|
| Probe lead 1 | A0 | GPIO 34 |
| Probe lead 2 | GND | GND |
| 10 k (or 100 k) resistor | 5 V to A0 | 3.3 V to GPIO 34 |
- Probe lead 1
- Arduino Uno:
- A0
- ESP32:
- GPIO 34
- Probe lead 2
- Arduino Uno:
- GND
- ESP32:
- GND
- 10 k (or 100 k) resistor
- Arduino Uno:
- 5 V to A0
- ESP32:
- 3.3 V to GPIO 34
Example code
A minimal sketch to check the part works.
const float R_FIXED = 10000.0; // divider resistor (use 100k for 100k probes)
const float R0 = 10000.0, T0 = 298.15, BETA = 3950.0;
void setup() { Serial.begin(115200); }
void loop() {
int a = analogRead(A0); // probe from A0 to GND, R_FIXED from 5 V to A0
float r = R_FIXED * a / (1023.0 - a);
float tK = 1.0 / (1.0 / T0 + log(r / R0) / BETA);
Serial.print(tK - 273.15, 1); Serial.println(" C");
delay(1000);
}Setup and tuning
wire the probe in a divider with a fixed resistor equal to its 25 °C value (often 10 kΩ).
read on an analog pin and convert with the Beta equation.
use the probe's B value, often 3435 or 3950.
long cables add resistance; keep them reasonable or calibrate.
check the probe's IP rating for liquids.
What you need
Shop this list19 of 20 found in our store · ₹2,327
Generic B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 5 Meter Cable: the part this guide coversB3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 5 Meter Cable₹98
B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 4 Meter Cable: another version this guide coversB3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 4 Meter Cable₹108
Generic B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with 2Meter Cable & XH2.54 Connector: another version this guide coversB3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with 2Meter Cable & XH2.54 Connector₹77
B3950 10K NTC Thermistor Temperature Sensor 5x20mm Stainless Steel Probe w/ 0.5m Cable & XH2.54 Connector: another version this guide coversB3950 10K NTC Thermistor Temperature Sensor 5x20mm Stainless Steel Probe w/ 0.5m Cable & XH2.54 Connector₹46
B3950 100K NTC Thermistor Temperature Sensor 3x20mm Stainless Steel Probe w/ 1m Cable & XH2.54 Connector: another version this guide coversB3950 100K NTC Thermistor Temperature Sensor 3x20mm Stainless Steel Probe w/ 1m Cable & XH2.54 Connector₹63
B3950 100K NTC Thermistor Temperature Sensor 3x25mm with XH2.54 Connector & 1 Meter Cable: another version this guide coversB3950 100K NTC Thermistor Temperature Sensor 3x25mm with XH2.54 Connector & 1 Meter Cable₹64
NTC B3950 100K Thermistor 1% with 1m Cable & 2-Pin Terminal: another version this guide coversNTC B3950 100K Thermistor 1% with 1m Cable & 2-Pin Terminal₹49
Generic Glass-sealed 100K Ohm NTC 3950 Thermistors 1%: another version this guide coversGlass-sealed 100K Ohm NTC 3950 Thermistors 1%₹17
Focusens Thermistor Temperature Sensor Probe – Waterproof TPE Plastic Overmolding, 3M Cable: another version this guide coversFocusens Thermistor Temperature Sensor Probe – Waterproof TPE Plastic Overmolding, 3M Cable₹174
Focusens NTC 10k Temperature Sensor for Pipe – Easy Installation: another version this guide coversFocusens NTC 10k Temperature Sensor for Pipe – Easy Installation₹65
Focusens Bullet Type NTC Temperature Sensor 10K 3950 for Coffee Machine: another version this guide coversFocusens Bullet Type NTC Temperature Sensor 10K 3950 for Coffee Machine₹84
Focusens NTC RTD Duct Temperature Sensor for HVAC System – 2.5m Cable: another version this guide coversFocusens NTC RTD Duct Temperature Sensor for HVAC System – 2.5m Cable₹629
Focusens Ring Terminal NTC BMS Temperature Sensor: another version this guide coversFocusens Ring Terminal NTC BMS Temperature Sensor₹66
Focusens 5K NTC Thermistor Retainer Temperature Sensor for Refrigerator Defroster Sensor: another version this guide coversFocusens 5K NTC Thermistor Retainer Temperature Sensor for Refrigerator Defroster Sensor₹110
Focusens MF5A-5 103F3977BT461 NTC Thermistor – 10 kΩ at 25°C, B3977K: another version this guide coversFocusens MF5A-5 103F3977BT461 NTC Thermistor – 10 kΩ at 25°C, B3977K₹58
DALY Smart BMS NTC (K TYPE) Temperature Sensor: another version this guide coversDALY Smart BMS NTC (K TYPE) Temperature Sensor₹83- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Metal film resistor 1/4 W 1% (pack of 10): a 10 k reference resistor for the dividerMetal Film Resistor 1/4W 1% (Pack of 10)₹8
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- NTC thermistors: the bare parts and theory.
- DS18B20 probe: digital, no calibration maths.
- Hotend heaters and thermistors: 100k probes in 3D printers.
Common mistakes to avoid
- Wrong B value.
- Wrong fixed resistor.
- Using non-sealed probes in liquid.
- Ignoring self-heating.
Frequently asked questions
Which resistor goes with a 10K NTC probe?
Use a 10 kΩ fixed resistor in a voltage divider with the probe.
How accurate are NTC probes?
About ±0.5 to ±1 °C with a good B value and calibration.
Can I use it in water?
Yes, if it is a sealed waterproof probe; check the IP rating first.
Why does reading change with cable length?
Long wires add resistance and error; calibrate the probe with its cable fitted.
What B value should I use?
Use the B value from the probe's datasheet, often 3950 or 3435.
Parts for this guide
B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 5 Meter Cable₹98View
B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with XH2.54 Connector & 4 Meter Cable₹108View
B3950 10K NTC Thermistor Temperature Sensor 5x25mm Stainless Steel Probe with 2Meter Cable & XH2.54 Connector₹77View
B3950 10K NTC Thermistor Temperature Sensor 5x20mm Stainless Steel Probe w/ 0.5m Cable & XH2.54 Connector₹46View
B3950 100K NTC Thermistor Temperature Sensor 3x20mm Stainless Steel Probe w/ 1m Cable & XH2.54 Connector₹63View- ₹64View
- ₹49View
- ₹17View
- ₹174View
- ₹65View
- ₹84View
- ₹629View
- ₹66View
- ₹110View
- ₹58View
- ₹83View
- ₹359View
- ₹389View
- ₹8View
- ₹139View
- ₹91View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


