Component guide · Beginner · 5 min read
Raspberry Pi GPIO Breakouts and Adapter Boards

T-Cobbler, Terminal Blocks, Proto HATs, HAT Hacker, Pi 400 Bases, Grove, Gravity, Crowtail and Pmod
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards make the Pi's 40-pin header easier to use. T-cobblers bring the pins to a breadboard, terminal block boards take screw wires, proto HATs let you solder your own circuit, splitters and HAT Hackers run two HATs at once, and Pi 400 bases expose the keyboard's rear header. Grove, Gravity, Crowtail and Pmod adapters plug in sensor modules without wiring.
Key specs at a glance
- Header
- 40-pin Raspberry Pi GPIO
- Types
- Cobbler, terminal block, proto, splitter, reference card
- Sensor systems
- Grove, Gravity, Crowtail, Pmod, Breakout Garden
- Logic
- 3.3V GPIO (8-channel level shifter for 5V parts)
- Pi models
- All 40-pin Pis and Pi 400
- Extras
- Analog inputs on GrovePi+ and Gravity IO HAT
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 140-Pin T-Type GPIO Extension Board for Raspberry Pi₹85
Option 2U-Shaped 40-Pin GPIO Expansion Board for Pi 3 B+₹219
Option 3Raspberry Pi 3 GPIO Expansion Board w/ Terminal Blocks₹449
Option 4Raspberry Pi GPIO 1-to-3 Expansion Board₹319
Option 540-Pin Prototype Pi Plate for Raspberry Pi 3/4B₹869
Option 6Raspberry Pi Proto HAT Shield for Pi 3/4B₹209
What the Raspberry Pi GPIO breakout, prototyping and adapter boards is
Pi GPIO breakout and prototyping boards, such as T-cobblers, screw-terminal HATs and proto HATs, bring the Raspberry Pi's 40-pin header to a breadboard or solder area.
The Pi's GPIO is 3.3V and not 5V tolerant. Use the 8-channel level converter for 5V sensors and modules.
The GrovePi+ and Gravity IO HAT add an analog-to-digital converter, because the Pi has no analog inputs. The ARPI600 adapter lets Arduino shields plug into a Pi.
Raspberry Pi GPIO breakout, prototyping and adapter boards pinout
The pins on the Raspberry Pi GPIO breakout, prototyping and adapter boards and what each one does.
| Pin | Function |
|---|---|
| 3.3V and 5V | Pins 1 and 2, 17 and 4 |
| GND | Pins 6, 9, 14, 20, 25, 30, 34, 39 |
| I2C | GPIO2 SDA, GPIO3 SCL |
| SPI0 | GPIO10 MOSI, 9 MISO, 11 SCLK, 8 CE0 |
| UART | GPIO14 TX, GPIO15 RX |
- 3.3V and 5V
- Pins 1 and 2, 17 and 4
- GND
- Pins 6, 9, 14, 20, 25, 30, 34, 39
- I2C
- GPIO2 SDA, GPIO3 SCL
- SPI0
- GPIO10 MOSI, 9 MISO, 11 SCLK, 8 CE0
- UART
- GPIO14 TX, GPIO15 RX
Wiring the Raspberry Pi GPIO breakout, prototyping and adapter boards
Line the ribbon's red stripe up with pin 1 (the corner nearest the microSD slot). A reversed ribbon can short 5V to a GPIO.
| Raspberry Pi GPIO breakout, prototyping and adapter boards pin | Connection | Note |
|---|---|---|
| T-cobbler | 40-pin ribbon to the Pi, board across the breadboard centre | Red stripe to pin 1 |
| Terminal board | Stack on the header | Tighten screws gently |
| Sensor adapter | Stack on the header, plug modules into ports | Check 3.3V or 5V select |
- T-cobbler
- Connection:
- 40-pin ribbon to the Pi, board across the breadboard centre
- Note:
- Red stripe to pin 1
- Terminal board
- Connection:
- Stack on the header
- Note:
- Tighten screws gently
- Sensor adapter
- Connection:
- Stack on the header, plug modules into ports
- Note:
- Check 3.3V or 5V select
Example code
Run pinout on the Pi to print the header map. For Grove and Gravity HATs install the maker's Python library to read their analog ports.
from gpiozero import LED, Button
from signal import pause
led = LED(17) # GPIO17 -> 330 ohm -> LED -> GND
btn = Button(27) # GPIO27 -> button -> GND (internal pull-up)
btn.when_pressed = led.on
btn.when_released = led.off
pause()Setup and tuning
match pin 1 (square pad or stripe on the ribbon) to pin 1 on the Pi header.
use the printed BCM numbers in code with gpiozero or RPi.GPIO.
Pi GPIO is 3.3 V and not 5 V tolerant; use level shifters for 5 V parts.
each pin should supply only a few mA; drive LEDs with resistors and loads with transistors.
the 5 V pins connect straight to the supply; never short them to GPIO.
What you need
Shop this list20 of 20 found in our store · ₹13,973
40-Pin T-Type GPIO Extension Board for Raspberry Pi: the part this guide covers40-Pin T-Type GPIO Extension Board for Raspberry Pi₹85
U-Shaped 40-Pin GPIO Expansion Board for Pi 3 B+: another version this guide coversU-Shaped 40-Pin GPIO Expansion Board for Pi 3 B+₹219
Raspberry Pi 3 GPIO Expansion Board w/ Terminal Blocks: another version this guide coversRaspberry Pi 3 GPIO Expansion Board w/ Terminal Blocks₹449
Raspberry Pi GPIO 1-to-3 Expansion Board: another version this guide coversRaspberry Pi GPIO 1-to-3 Expansion Board₹319
40-Pin Prototype Pi Plate for Raspberry Pi 3/4B: another version this guide covers40-Pin Prototype Pi Plate for Raspberry Pi 3/4B₹869
Raspberry Pi Proto HAT Shield for Pi 3/4B: another version this guide coversRaspberry Pi Proto HAT Shield for Pi 3/4B₹209
Raspberry Pi 40-Pin GPIO Reference Board: another version this guide coversRaspberry Pi 40-Pin GPIO Reference Board₹21
Raspberry Pi GPIO BCM Pinout Reference Board: another version this guide coversRaspberry Pi GPIO BCM Pinout Reference Board₹93
Raspberry Pi GPIO Quick Reference Ruler V2: another version this guide coversRaspberry Pi GPIO Quick Reference Ruler V2₹129
SparkFun GPIO Tall Header – 2×20 Pin for Raspberry Pi: another version this guide coversSparkFun GPIO Tall Header – 2×20 Pin for Raspberry Pi₹439
Pimoroni HAT Hacker HAT for Raspberry Pi: another version this guide coversPimoroni HAT Hacker HAT for Raspberry Pi₹1,009
Pimoroni Nano HAT Hacker for Raspberry Pi: another version this guide coversPimoroni Nano HAT Hacker for Raspberry Pi₹349
Cytron Maker Hat Base for Raspberry Pi 400 GPIO Extension: another version this guide coversCytron Maker Hat Base for Raspberry Pi 400 GPIO Extension₹1,252
EDATEC 40-pin I/O Protector for Pi 400: another version this guide coversEDATEC 40-pin I/O Protector for Pi 400₹1,050
EDATEC 40-pin I/O Protector for Raspberry Pi 400, Grey: another version this guide coversEDATEC 40-pin I/O Protector for Raspberry Pi 400, Grey₹1,050
Adafruit CYBERDECK Bonnet for Raspberry Pi 400: another version this guide coversAdafruit CYBERDECK Bonnet for Raspberry Pi 400₹1,179
Pimoroni Breakout Garden Mini (I2C + SPI) for Raspberry Pi: another version this guide coversPimoroni Breakout Garden Mini (I2C + SPI) for Raspberry Pi₹1,099
Raspberry Pi 8-Channel Bi-directional Logic Level Converter: another version this guide coversRaspberry Pi 8-Channel Bi-directional Logic Level Converter₹95
Waveshare ARPI600 Adapter Board for Arduino & Raspberry Pi: another version this guide coversWaveshare ARPI600 Adapter Board for Arduino & Raspberry Pi₹2,499
DFRobot Gravity Arduino Shield for Raspberry Pi: another version this guide coversDFRobot Gravity Arduino Shield for Raspberry Pi₹1,559
Alternatives and when to choose them
- Pi HATs explained: stacking rules.
- Pi models compared: header and pin differences.
- ADS1115 ADC: add analog inputs.
Common mistakes to avoid
- Reversing the ribbon cable.
- Connecting 5 V signals to GPIO.
- Driving motors straight from pins.
- Mixing BCM and board pin numbers.
Frequently asked questions
Which pin numbers should I use in code?
Use the BCM GPIO numbers printed on most breakouts, which gpiozero uses by default.
Can I connect 5 V sensors to the Pi GPIO?
No. Pi pins are 3.3 V only; use a level shifter or divider.
Why does my ribbon cable breakout not work?
The ribbon is probably reversed; match the stripe to pin 1.
How much current can a GPIO pin give?
Keep it to a few mA per pin, and about 50 mA across all pins.
Can I solder a circuit onto a proto HAT?
Yes. Proto HATs let you build a permanent circuit that plugs onto the Pi.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.








