Component guide · Intermediate · 6 min read
Laser PM Sensors

Plantower PMS1003, PMS3003, PMS5303, PMS6003, PMS9003M and PMSA003, MemsFrontier MPM10, MPM11, MPM12, MPM14 and MPM60, Winsen ZH03B, ZH06-I and ZH07, Asair APM10, Panasonic SN-GCJA5, Sensirion SPS30, ACEBOTT and DFRobot Gravity PM2.5
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Laser PM sensors use a fan and a laser to count particles, then report PM1.0, PM2.5 and PM10 in µg/m³ over UART, with I2C or PWM on some. Plantower PMS and PMSA003, Winsen ZH and MemsFrontier MPM models differ mainly in size, airflow direction and connector. Sensirion SPS30 and Panasonic SN-GCJA5 are long-life, factory-calibrated options. MPM60 is an automotive LIN version.
Key specs at a glance
- Outputs
- PM1.0, PM2.5, PM10 mass; particle counts on many
- Interface
- UART 9600 baud typical; I2C on SPS30, SN-GCJA5, MPM, DFRobot Gravity; PWM on some
- Range
- 0-500 or 0-1000 µg/m³ effective
- Supply
- 5V for the fan, 3.3V logic on most
- Connectors
- 1.25mm or 1.27mm pitch; MPM 8-pin or 10-pin, MPM12 GH1.25
- Life
- Fan life 3 to 8 years; SPS30 over 8 years
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Plantower PMS1003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V DC₹1,739
Option 2Plantower PMS3003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹1,519
Option 3Plantower PMS5303 PM2.5 Laser Particle Concentration Sensor – UART, 0~500 µg/m³, 5V₹1,809
Option 4Plantower PMS6003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹2,719
Option 5Plantower PMS9003M PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹2,109
Option 6Plantower PMSA003-A PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹1,779
What the Laser PM2.5 sensors: Plantower PMS series, MemsFrontier MPM, Winsen ZH, Sensirion SPS30 and Panasonic SN-GCJA5 is
Plantower PMS5003, PMS7003, PMSA003 and similar laser PM sensors count dust particles with a laser and fan to report PM1.0, PM2.5 and PM10 for air quality monitors.
Pick by size and airflow: MPM -A models have side inlets, -B front, -C opposite sides, which matters inside a small enclosure. PMSA003 is very thin for portable monitors. SPS30 is the choice for long-running stations because it self-cleans the fan.
Most sensors send a frame every second in active mode. Use sleep or passive mode to save fan life on battery devices, and wake the sensor for 30 seconds before taking a reading. Above about 80% humidity, fog and water droplets read as particles.
Laser PM2.5 sensors: Plantower PMS series, MemsFrontier MPM, Winsen ZH, Sensirion SPS30 and Panasonic SN-GCJA5 pinout
The pins on the Laser PM2.5 sensors: Plantower PMS series, MemsFrontier MPM, Winsen ZH, Sensirion SPS30 and Panasonic SN-GCJA5 and what each one does.
| Pin | Function |
|---|---|
| VCC | 5V fan supply |
| GND | Ground |
| TX / RX | UART, 3.3V levels |
| SET | Sleep control on Plantower |
| RESET | Reset, pull high |
- VCC
- 5V fan supply
- GND
- Ground
- TX / RX
- UART, 3.3V levels
- SET
- Sleep control on Plantower
- RESET
- Reset, pull high
Wiring the Laser PM2.5 sensors: Plantower PMS series, MemsFrontier MPM, Winsen ZH, Sensirion SPS30 and Panasonic SN-GCJA5
Use the maker's adapter cable or a 1.25mm breakout; these connectors are too fine for jumper wires.
| Laser PM2.5 sensors: Plantower PMS series, MemsFrontier MPM, Winsen ZH, Sensirion SPS30 and Panasonic SN-GCJA5 pin | ESP32 | Note |
|---|---|---|
| VCC | 5V | Fan needs about 100 mA |
| Sensor TX | ESP32 GPIO16 (RX2) | 3.3V logic |
| Sensor RX | ESP32 GPIO17 (TX2) | For passive mode commands |
| SET | 3.3V or a GPIO | LOW sleeps the sensor |
- VCC
- ESP32:
- 5V
- Note:
- Fan needs about 100 mA
- Sensor TX
- ESP32:
- ESP32 GPIO16 (RX2)
- Note:
- 3.3V logic
- Sensor RX
- ESP32:
- ESP32 GPIO17 (TX2)
- Note:
- For passive mode commands
- SET
- ESP32:
- 3.3V or a GPIO
- Note:
- LOW sleeps the sensor
Example code
SPS30 and SN-GCJA5 use their own frames and I2C registers; use the Sensirion or Panasonic library for those.
// Plantower-style 32-byte frame: 0x42 0x4D, length, then data words.
// Most MemsFrontier and Winsen sensors use a similar active-mode frame;
// check the datasheet for the exact header and byte positions.
#define RXD 16
#define TXD 17
uint8_t buf[32];
void setup() {
Serial.begin(115200);
Serial2.begin(9600, SERIAL_8N1, RXD, TXD);
}
bool readFrame() {
while (Serial2.available() >= 32) {
if (Serial2.read() != 0x42) continue;
if (Serial2.peek() != 0x4D) continue;
buf[0] = 0x42;
Serial2.readBytes(buf + 1, 31);
uint16_t sum = 0;
for (int i = 0; i < 30; i++) sum += buf[i];
return sum == ((buf[30] << 8) | buf[31]);
}
return false;
}
void loop() {
if (readFrame()) {
uint16_t pm1 = (buf[10] << 8) | buf[11]; // atmospheric values
uint16_t pm25 = (buf[12] << 8) | buf[13];
uint16_t pm10 = (buf[14] << 8) | buf[15];
Serial.printf("PM1.0 %u PM2.5 %u PM10 %u ug/m3\n", pm1, pm25, pm10);
}
delay(200);
}Setup and tuning
5 V power for the fan, GND, and TX/RX at 3.3 V logic to the microcontroller UART at 9600 baud.
use the PMS library or Adafruit PM25AQI library.
wait 30 s after waking before reading.
sleep the sensor between readings to extend fan and laser life.
keep inlets clear and away from direct wind and rain.
What you need
Shop this list20 of 20 found in our store · ₹28,945
Plantower PMS1003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V DC: the part this guide coversPlantower PMS1003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V DC₹1,739
Plantower PMS3003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V: another version this guide coversPlantower PMS3003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹1,519
Plantower PMS5303 PM2.5 Laser Particle Concentration Sensor – UART, 0~500 µg/m³, 5V: another version this guide coversPlantower PMS5303 PM2.5 Laser Particle Concentration Sensor – UART, 0~500 µg/m³, 5V₹1,809
Plantower PMS6003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V: another version this guide coversPlantower PMS6003 PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹2,719
Plantower PMS9003M PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V: another version this guide coversPlantower PMS9003M PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹2,109
Plantower PMSA003-A PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V: another version this guide coversPlantower PMSA003-A PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V₹1,779
Plantower PMSA003-C PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V DC: another version this guide coversPlantower PMSA003-C PM2.5 Laser Particle Concentration Sensor, UART, 0~500 µg/m³, 5V DC₹1,639
MemsFrontier MPM10-AD Laser PM Sensor (Side Air Inlet/Outlet, 10-Pin): another version this guide coversMemsFrontier MPM10-AD Laser PM Sensor (Side Air Inlet/Outlet, 10-Pin)₹1,194
MemsFrontier MPM10-AS Laser PM Sensor – Side Air Inlet/Outlet, 8-Pin, UART/I2C/PWM: another version this guide coversMemsFrontier MPM10-AS Laser PM Sensor – Side Air Inlet/Outlet, 8-Pin, UART/I2C/PWM₹1,119
MemsFrontier MPM10-BD Laser PM Sensor Module – UART/I2C/PWM Output, Front Airflow: another version this guide coversMemsFrontier MPM10-BD Laser PM Sensor Module – UART/I2C/PWM Output, Front Airflow₹989
MemsFrontier MPM10-BS Laser PM Sensor (Front Air Inlet/Outlet, 8-Pin): another version this guide coversMemsFrontier MPM10-BS Laser PM Sensor (Front Air Inlet/Outlet, 8-Pin)₹1,145
MemsFrontier MPM10-CD Laser PM Sensor (Opposite Side Inlet/Outlet, 10-Pin): another version this guide coversMemsFrontier MPM10-CD Laser PM Sensor (Opposite Side Inlet/Outlet, 10-Pin)₹1,129
MemsFrontier MPM10-CS Laser PM Sensor – UART/I2C/PWM Output, 8-Pin: another version this guide coversMemsFrontier MPM10-CS Laser PM Sensor – UART/I2C/PWM Output, 8-Pin₹1,089
MemsFrontier MPM11-AD Laser PM Sensor Module – Side Air Inlets/Outlets, 10-Pin, UART/I2C/PWM Output: another version this guide coversMemsFrontier MPM11-AD Laser PM Sensor Module – Side Air Inlets/Outlets, 10-Pin, UART/I2C/PWM Output₹1,029
MemsFrontier MPM11-BD Laser PM Sensor Module – Front Air Inlet/Outlet, 10-Pin, UART/I2C/PWM: another version this guide coversMemsFrontier MPM11-BD Laser PM Sensor Module – Front Air Inlet/Outlet, 10-Pin, UART/I2C/PWM₹1,049
MemsFrontier MPM11-BS Laser PM Sensor (Front Air Inlet/Outlet, 8-Pin) – UART/I2C/PWM Output: another version this guide coversMemsFrontier MPM11-BS Laser PM Sensor (Front Air Inlet/Outlet, 8-Pin) – UART/I2C/PWM Output₹1,049
MemsFrontier MPM12-BG Laser PM Sensor (Air Inlet/Outlet Front, GH1.25mm Connector): another version this guide coversMemsFrontier MPM12-BG Laser PM Sensor (Air Inlet/Outlet Front, GH1.25mm Connector)₹1,173
MemsFrontier MPM14-CS Laser PM Sensor (Opposite Side Air Inlet/Outlet, 8-Pin): another version this guide coversMemsFrontier MPM14-CS Laser PM Sensor (Opposite Side Air Inlet/Outlet, 8-Pin)₹1,129
MemsFrontier MPM60-C4 Vehicle PM Sensor – LIN Output: another version this guide coversMemsFrontier MPM60-C4 Vehicle PM Sensor – LIN Output₹2,209
Winsen ZH03B Laser Dust Sensor PM2.5 PM10 PM1.0 – UART & PWM Output: another version this guide coversWinsen ZH03B Laser Dust Sensor PM2.5 PM10 PM1.0 – UART & PWM Output₹1,329
Alternatives and when to choose them
- PMS5003 and PMS7003: the most common Plantower models.
- SDS011: larger laser sensor.
- Sharp and infrared dust sensors: cheaper trend sensors.
Common mistakes to avoid
- Powering the fan from 3.3 V.
- Running it continuously without sleep.
- Blocking the inlet.
- Ignoring humidity effects.
Frequently asked questions
What is the difference between PM2.5 and PM10?
PM2.5 counts particles under 2.5 µm; PM10 under 10 µm.
Why do readings jump in humid weather?
Water droplets are counted as particles at high humidity.
Can I read it with ESP32?
Yes, over UART at 9600 baud, with 5 V power.
How long does the sensor last?
About 3 years of continuous use; longer with sleep cycles.
Is it as accurate as a reference monitor?
No. It shows trends; correct for humidity for better results.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.









