Component guide · Intermediate · 4 min read
SCT-013 AC Current Sensor

Wiring, Burden Resistor and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The SCT-013 is a split-core current transformer that clips around one mains wire to measure AC current without cutting or touching the wire. The 100 A version outputs a current and needs a burden resistor; the 30 A (SCT-013-030) has the resistor built in and outputs about 1 V. A small bias circuit centres the signal for the Arduino ADC, and EmonLib turns it into amps.
Key specs at a glance
- Type
- Split-core AC current transformer
- Range
- 0 to 100 A (SCT-013-000) or 0 to 30 A (SCT-013-030)
- Output
- 50 mA current (100 A model) or 1 V voltage (30 A model)
- Connector
- 3.5 mm jack
- Accuracy
- About ±1 to 3 % with a good burden and calibration
- Opening
- 13 mm, fits one cable
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the SCT-013 current transformer is
The clamp acts as a transformer: the mains wire is the primary and the coil inside is the secondary. The output is AC and swings above and below zero, so it is added to a 2.5 V (or 1.65 V on an ESP32) bias made with two resistors and a capacitor, then read on an analog pin.
The sensor itself never touches mains voltage, which makes it the safest way to monitor home energy use. Clip it around the live or the neutral wire only, never the whole cable.
SCT-013 current transformer pinout
The pins on the SCT-013 current transformer and what each one does.
| Pin | Function |
|---|---|
| Jack tip | Signal |
| Jack sleeve | Signal return |
| Burden resistor | Across tip and sleeve (100 A model only, about 22 to 33 ohm on 3.3 V) |
| Bias divider | Two 10 kΩ resistors from supply to GND with a 10 µF capacitor; midpoint to sleeve |
- Jack tip
- Signal
- Jack sleeve
- Signal return
- Burden resistor
- Across tip and sleeve (100 A model only, about 22 to 33 ohm on 3.3 V)
- Bias divider
- Two 10 kΩ resistors from supply to GND with a 10 µF capacitor; midpoint to sleeve
Wiring the SCT-013 current transformer
For the 100 A model on 5 V, a 33 ohm burden gives about 2.3 V peak at 100 A; on a 3.3 V ESP32 use 22 ohm. The 30 A model already contains its burden: add only the bias circuit.
| SCT-013 current transformer pin | Arduino Uno | ESP32 |
|---|---|---|
| Tip | A1 (through the bias circuit) | GPIO 34 (through the bias circuit) |
| Sleeve | Bias midpoint (2.5 V) | Bias midpoint (1.65 V) |
| Bias top | 5V | 3V3 |
| Bias bottom | GND | GND |
- Tip
- Arduino Uno:
- A1 (through the bias circuit)
- ESP32:
- GPIO 34 (through the bias circuit)
- Sleeve
- Arduino Uno:
- Bias midpoint (2.5 V)
- ESP32:
- Bias midpoint (1.65 V)
- Bias top
- Arduino Uno:
- 5V
- ESP32:
- 3V3
- Bias bottom
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Calibration = turns ratio / burden ohms: 2000 / 33 = 60.6 for the 100 A model, and 30 for the 30 A model. Check against a clamp meter and adjust.
#include "EmonLib.h"
EnergyMonitor emon;
void setup() {
Serial.begin(115200);
emon.current(A1, 60.6); // 100 A / 0.05 A / 33 ohm = 60.6 (calibration)
}
void loop() {
double irms = emon.calcIrms(1480); // samples
Serial.print(irms, 2); Serial.print(" A ");
Serial.print(irms * 230.0, 0); Serial.println(" W (approx at 230 V)");
delay(1000);
}Setup and tuning
clamp the live (or neutral) conductor; around a whole cable the currents cancel to zero.
the open output can reach high voltages.
compare with a clamp meter on a known load such as a kettle.
below about 0.5 A readings are noisy; wrap the wire through the clamp twice and halve the result.
What you need
Shop this list7 of 8 found in our store · ₹1,733
YHDC SCT-013 100A Non-Invasive AC Current Sensor (Split Core): the part this guide coversYHDC SCT-013 100A Non-Invasive AC Current Sensor (Split Core)₹365
YHDC SCT-013-030 30A Split-Core Current Transformer: another version this guide coversYHDC SCT-013-030 30A Split-Core Current Transformer₹397- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Resistor assortment kit: for pull-ups, dividers and gate resistorsResistor Assortment Kit₹250
Electrolytic capacitor: 10 µF for the bias circuitElectrolytic Capacitor₹16
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- ACS712 current sensor: the current flows through the board, for DC or low AC currents.
- INA3221 current monitor: DC rails up to 26 V.
- Hall effect sensors: how Hall sensing works for DC and AC current.
Try it: Ohms law calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Clamping the whole cable, so live and neutral cancel out.
- Using the 100 A model without a burden resistor.
- Feeding the AC output straight into an analog pin without the bias circuit.
- Opening an electrical panel without the skills to do it safely.
Frequently asked questions
What is the difference between SCT-013-000 and SCT-013-030?
The 000 (100 A) gives a current output and needs a burden resistor; the 030 (30 A) gives a voltage and has the resistor inside.
Does it measure power?
It measures current; multiply by the mains voltage for an estimate, or add a voltage sensor for real power.
Can it measure DC?
No, a current transformer only works with AC.
Is it safe?
The sensor does not touch the conductor, but fitting it in a panel is mains work; have an electrician do it.
Does it work with ESP32?
Yes, use a 1.65 V bias and an ADC1 pin.
Parts for this guide
Calculators
Keep learning
Sources
- YHDC SCT-013 split-core current transformer datasheet
- OpenEnergyMonitor CT sensor interfacing documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


