Component guide · Beginner · 3 min read
Ultrasonic Mist Maker and Humidifier Module (5V USB and 24V)

Wiring and Control
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
An ultrasonic mist maker uses a piezo disc vibrating at about 108 kHz to 1.7 MHz to break water into a fine cold mist. The 5 V USB modules use a cotton wick and a small driver board, suitable for desk humidifiers and terrariums. Larger 24 V foggers sit under water. Both must never run dry, or the disc cracks.
Key specs at a glance
- Voltage
- 5 V USB modules; 24 V for submerged foggers
- Current
- About 300 to 500 mA (5 V)
- Frequency
- About 108 kHz (USB) or 1.7 MHz (fogger)
- Mist output
- About 20 to 40 mL/h (5 V)
- Water
- Clean water, low mineral
- Control
- Button on board or power switching
What the Ultrasonic mist maker module is
An ultrasonic mist maker uses a piezo disc that vibrates far above hearing range. The vibration breaks water into a fine, cold mist, which is how small humidifiers and foggers work.
The driver board has its own oscillator; switch its power with a MOSFET or relay. Many 5 V boards have a button that toggles modes and start off after power-up, so check whether yours starts automatically.
Hard water leaves white dust; use filtered water.
Ultrasonic mist maker module pinout
The pins on the Ultrasonic mist maker module and what each one does.
| Pin | Function |
|---|---|
| 5V / GND | Driver board power |
| Piezo | Two wires to the disc |
| Button | Mode on some boards |
- 5V / GND
- Driver board power
- Piezo
- Two wires to the disc
- Button
- Mode on some boards
Wiring the Ultrasonic mist maker module
Connect the Ultrasonic mist maker module like this.
| Ultrasonic mist maker module pin | Arduino Uno | ESP32 |
|---|---|---|
| 5V | 5 V supply | 5 V supply |
| GND | MOSFET module OUT- | MOSFET module OUT- |
| Module signal | D7 | GPIO 26 |
- 5V
- Arduino Uno:
- 5 V supply
- ESP32:
- 5 V supply
- GND
- Arduino Uno:
- MOSFET module OUT-
- ESP32:
- MOSFET module OUT-
- Module signal
- Arduino Uno:
- D7
- ESP32:
- GPIO 26
Example code
A minimal sketch to check the part works.
#include <DHT.h>
DHT dht(2, DHT22);
const int MIST = 7;
void setup() { pinMode(MIST, OUTPUT); dht.begin(); }
void loop() {
float h = dht.readHumidity();
if (!isnan(h)) digitalWrite(MIST, h < 60 ? HIGH : LOW);
delay(5000);
}Setup and tuning
switch the driver board's supply with a MOSFET or relay; it has its own oscillator.
many 5 V boards start off after power-up and need a button press; check yours, or choose one that starts automatically.
add a level sensor so it switches off before the water runs out.
use filtered or low-mineral water to avoid white dust and scale.
keep the cotton wick wet and replace it when it hardens.
What you need
Shop this list3 of 4 found in our store · ₹777
Ultrasonic Mist Maker Module: the part this guide coversUltrasonic Mist Maker Module₹349- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
MOSFET switch module (D4184 / LR7843): to switch or PWM it from a GPIOMOSFET Switch Module, Relay Replacement (D4184 / LR7843)₹39
Alternatives and when to choose them
Common mistakes to avoid
- Running it without water, which cracks the disc.
- Using hard tap water that leaves white dust.
- Letting the mist settle on electronics.
- Powering it from a supply that cannot give 500 mA.
Frequently asked questions
Is the mist from an ultrasonic mist maker hot?
No. It is cold mist made by vibration, not by heating.
Can an Arduino switch a mist maker?
Yes. Switch its supply with a MOSFET or relay, and check whether the board needs a button press after power-up.
How long does the piezo disc last?
Thousands of hours with clean water. Hard water and dry running shorten its life.
Can I add essential oils?
Avoid it. Oils damage the disc and the plastic parts.
Why is my mist maker not making mist?
The wick may be dry, the board may be in the off mode, or the supply cannot give enough current.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

