Component guide · Beginner · 4 min read
USB to RS485 Converter

Drivers, Wiring and Testing Modbus Devices from a PC
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A USB to RS485 converter gives a PC or Raspberry Pi a COM port that talks on an RS485 bus. It is the first tool to reach for with Modbus energy meters, VFDs and sensors: connect A, B and ground, open a Modbus program and read registers before writing any controller code. Isolated versions protect the computer from ground differences and surges on long industrial cables.
Key specs at a glance
- Chips
- CH340, CH343G or FT232RNL USB UART with an RS485 transceiver
- Ports
- 1 or 4 channels; some also offer RS232 and TTL
- Isolation
- Isolated versions use digital isolators and an isolated DC-DC
- Baud rate
- 300 bps to 3 Mbps depending on chip
- Direction
- Automatic transmit/receive switching
- Protection
- TVS and resettable fuses on industrial versions
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1USB to RS485 Converter Adapter₹74
Option 2Waveshare Industrial USB to RS485 Bidirectional Converter, CH343G₹774
Option 3Waveshare Industrial USB to RS485 / RS422 Isolated Converter₹1,699
Option 4Waveshare USB to RS485 Isolated Converter (FT232RNL)₹1,750
Option 5Waveshare Industrial USB to RS232 / RS485 / TTL Converter₹2,171
Option 6Waveshare Industrial USB to 4-Channel RS485 Converter₹1,950
What the USB to RS485 converter is
RS485 is half duplex: the converter switches its driver on while the PC sends and back to receive automatically, so ordinary serial programs work. Windows 10 and Linux include CH340 and FTDI drivers; the CH343G may need the WCH driver on older systems.
The TTL to RS485 (C) isolated module does the same job for a microcontroller UART, and the isolated RS485 hub splits one bus into isolated branches.
USB to RS485 converter pinout
The pins on the USB to RS485 converter and what each one does.
| Pin | Function |
|---|---|
| A / D+ / 485+ | Non-inverting bus line |
| B / D- / 485- | Inverting bus line |
| GND / SGND | Signal ground (isolated ground on isolated versions) |
| RJ45 (some models) | A, B and GND on the pins listed in the manual |
| 120R switch | Built-in termination on some converters |
- A / D+ / 485+
- Non-inverting bus line
- B / D- / 485-
- Inverting bus line
- GND / SGND
- Signal ground (isolated ground on isolated versions)
- RJ45 (some models)
- A, B and GND on the pins listed in the manual
- 120R switch
- Built-in termination on some converters
Wiring the USB to RS485 converter
If nothing answers, swap A and B: makers do not agree on the labels. Do not connect the converter ground to mains earth at both ends of a long cable; use an isolated converter instead.
| USB to RS485 converter pin | Device bus | MAX485 module on an Arduino |
|---|---|---|
| A+ | A+ of every device | A+ |
| B- | B- of every device | B- |
| GND | Signal ground or shield | GND |
- A+
- Device bus:
- A+ of every device
- MAX485 module on an Arduino:
- A+
- B-
- Device bus:
- B- of every device
- MAX485 module on an Arduino:
- B-
- GND
- Device bus:
- Signal ground or shield
- MAX485 module on an Arduino:
- GND
Example code
Install with pip install minimalmodbus. On Linux the port is /dev/ttyUSB0. Free tools such as QModMaster or Modbus Poll do the same without code.
import minimalmodbus
dev = minimalmodbus.Instrument("COM5", 1) # port, Modbus slave address
dev.serial.baudrate = 9600
dev.serial.parity = "N"
dev.serial.timeout = 0.5
regs = dev.read_registers(0, 2, functioncode=3) # start 0, count 2
print("Registers:", regs)Setup and tuning
check Device Manager or ls /dev/ttyUSB* after plugging in.
read the device manual for address, baud rate, parity and register map.
a converter in receive-only use can watch traffic between a PLC and a device.
run A, B and a ground or shield wire; A to A and B to B on every device.
fit 120 ohm resistors only at the two ends of a long bus.
daisy-chain the devices; avoid stars and long stubs.
every device on one bus needs the same baud rate and parity and a unique Modbus address.
What you need
Shop this list12 of 12 found in our store · ₹92,851
USB to RS485 Converter Adapter: the part this guide coversUSB to RS485 Converter Adapter₹74
Waveshare Industrial USB to RS485 Bidirectional Converter, CH343G: another version this guide coversWaveshare Industrial USB to RS485 Bidirectional Converter, CH343G₹774
Waveshare Industrial USB to RS485 / RS422 Isolated Converter: another version this guide coversWaveshare Industrial USB to RS485 / RS422 Isolated Converter₹1,699
Waveshare USB to RS485 Isolated Converter (FT232RNL): another version this guide coversWaveshare USB to RS485 Isolated Converter (FT232RNL)₹1,750
Waveshare Industrial USB to RS232 / RS485 / TTL Converter: another version this guide coversWaveshare Industrial USB to RS232 / RS485 / TTL Converter₹2,171
Waveshare Industrial USB to 4-Channel RS485 Converter: another version this guide coversWaveshare Industrial USB to 4-Channel RS485 Converter₹1,950
Waveshare TTL to RS485 (C) Galvanic Isolated Converter: another version this guide coversWaveshare TTL to RS485 (C) Galvanic Isolated Converter₹696
Waveshare Isolated RS485 Hub: another version this guide coversWaveshare Isolated RS485 Hub₹1,250
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
MAX485 TTL to RS485 converter module: to put an Arduino or ESP32 on the same busKikobot C1 6-Axis Robotic Arm for Education and Research₹70,800
Raspberry Pi 4 Model B 4GB: a small Modbus master or Node-RED hostRaspberry Pi 4 Model B with 4GB RAM₹11,461Closest match, check the specs
Alternatives and when to choose them
- MAX485 RS485 module: RS485 for an Arduino or ESP32 instead of a PC.
- RS485 and RS232: how the two serial standards differ.
- Modbus RTU with Arduino and ESP32: the protocol on top.
Common mistakes to avoid
- Swapped A and B.
- No common ground on a non-isolated converter.
- Terminating every device instead of only the two ends.
- Wrong parity: many meters use 8E1, not 8N1.
Frequently asked questions
Which chip is best?
FT232RNL and CH343G are reliable; CH340 is fine for most tests.
Do I need an isolated converter?
Yes for long cables, motors, VFDs or outdoor runs; no for a bench test.
Can it do RS422?
The RS485/RS422 versions can; RS422 uses four wires.
Does it work with a Raspberry Pi?
Yes, it appears as /dev/ttyUSB0.
Why do I get no reply?
Check A/B, address, baud rate and parity, in that order.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

