Component guide · Beginner · 3 min read
VL6180X Time-of-Flight Proximity and Ambient Light Sensor

GY-6180, TOF050C, DFRobot, SparkFun)
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The VL6180X is a tiny ST time-of-flight sensor that measures how long a laser pulse takes to return. It gives a precise distance from about 0 to 10 cm (up to 20 cm in good conditions) regardless of target colour, plus an ambient light reading. It talks I2C at address 0x29. TOF050C, GY-6180, DFRobot and SparkFun boards carry it with a regulator and level shifting.
Key specs at a glance
- Range
- About 0 to 100 mm guaranteed, up to 200 mm
- Resolution
- 1 mm
- Interface
- I2C, 0x29 (changeable in software)
- Supply
- 2.7 to 5 V on breakouts
- Extras
- Ambient light sensor (lux)
- Laser
- 850 nm VCSEL, Class 1
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1DFRobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout) – I2C Interface₹1,359
Option 2GY-6180 VL6180X Distance and Gesture Sensor Module – Blue PCB, I2C Interface₹369
Option 3TOF050C Laser Ranging Sensor Module – VL6180 Chip, I2C Interface, 0-50cm Range₹249
Option 4TOF050C 400C Laser Ranging Sensor Module – VL6180 ToF, I2C Output₹58
Option 5TOF050C 200C Laser Ranging Sensor Module Protective Cover Plate₹58
Option 6VL6180X 3.3V/5V Ranging and Ambient Light Sensor Board Black₹259
What the VL6180X ToF proximity sensor is
The ST VL6180X is a short-range ToF distance sensor measuring 0 to 100 mm, plus ambient light, over I2C, ideal for close object detection.
Use it where you need a precise short distance: hand detection, liquid level in a cup, gripper feedback or a contactless button.
Several sensors on one bus need different addresses; hold others in reset with their GPIO0/CE pins while you change each address.
VL6180X ToF proximity sensor pinout
The pins on the VL6180X ToF proximity sensor and what each one does.
| Pin | Function |
|---|---|
| VIN | Supply |
| GND | Ground |
| SDA, SCL | I2C |
| GPIO0 / CE | Shutdown and address setting |
| GPIO1 | Interrupt |
- VIN
- Supply
- GND
- Ground
- SDA, SCL
- I2C
- GPIO0 / CE
- Shutdown and address setting
- GPIO1
- Interrupt
Wiring the VL6180X ToF proximity sensor
Connect the VL6180X ToF proximity sensor like this.
| VL6180X ToF proximity sensor pin | Arduino Uno | ESP32 |
|---|---|---|
| VIN | 5 V | 3.3 V |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VIN
- Arduino Uno:
- 5 V
- ESP32:
- 3.3 V
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
A minimal sketch to check the part works.
#include <Adafruit_VL6180X.h>
Adafruit_VL6180X vl;
void setup() {
Serial.begin(115200);
if (!vl.begin()) { Serial.println("No VL6180X"); while (1); }
}
void loop() {
uint8_t mm = vl.readRange();
if (vl.readRangeStatus() == VL6180X_ERROR_NONE) { Serial.print(mm); Serial.println(" mm"); }
Serial.print(vl.readLux(VL6180X_ALS_GAIN_5)); Serial.println(" lux");
delay(200);
}Setup and tuning
VCC, GND, SDA and SCL; GPIO0 for shutdown.
use the Adafruit VL6180X library.
0 to 100 mm accurately, sometimes up to 200 mm.
change addresses using shutdown pins.
use proper cover glass and calibration.
What you need
Shop this list10 of 11 found in our store · ₹6,681
DFRobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout) – I2C Interface: the part this guide coversDFRobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout) – I2C Interface₹1,359
Generic GY-6180 VL6180X Distance and Gesture Sensor Module – Blue PCB, I2C Interface: another version this guide coversGY-6180 VL6180X Distance and Gesture Sensor Module – Blue PCB, I2C Interface₹369
TOF050C Laser Ranging Sensor Module – VL6180 Chip, I2C Interface, 0-50cm Range: another version this guide coversTOF050C Laser Ranging Sensor Module – VL6180 Chip, I2C Interface, 0-50cm Range₹249
TOF050C 400C Laser Ranging Sensor Module – VL6180 ToF, I2C Output: another version this guide coversTOF050C 400C Laser Ranging Sensor Module – VL6180 ToF, I2C Output₹58
TOF050C 200C Laser Ranging Sensor Module Protective Cover Plate: another version this guide coversTOF050C 200C Laser Ranging Sensor Module Protective Cover Plate₹58
VL6180X 3.3V/5V Ranging and Ambient Light Sensor Board Black: another version this guide coversVL6180X 3.3V/5V Ranging and Ambient Light Sensor Board Black₹259
SparkFun VL6180 Time of Flight (ToF) Range Finder Sensor Module: another version this guide coversSparkFun VL6180 Time of Flight (ToF) Range Finder Sensor Module₹3,359- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
TowerPro SG90 micro servo: to sweep the sensor for a scanTowerPro SG90 9g Micro Servo (180°)₹442Closest match, check the specs
Alternatives and when to choose them
- VL53L0X ToF: up to about 2 m.
- VL53L4CX and TMF8801: longer range.
- IR obstacle modules: simple on or off.
Common mistakes to avoid
- Using it beyond 100 mm.
- Address conflicts.
- Cover glass crosstalk.
- No calibration.
Frequently asked questions
How far can the VL6180X measure?
It measures about 0 to 100 mm reliably, and sometimes a bit further.
Can I use it for robots?
Yes. It suits close obstacle and table-edge detection on small robots.
Why are readings capped at 255?
Anything beyond its range returns the maximum value of 255 mm.
Does it measure light?
Yes. It also has an ambient light sensor for lux readings.
Can I use multiple sensors?
Yes. Use the shutdown pins to give each sensor a new address at start-up.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

