Component guide · Beginner · 4 min read
Waveshare SPI LCD Modules and Raspberry Pi LCDs

0.85, 1.47, 1.69, 1.8, 1.9 and 2 Inch IPS Modules, 2.8 to 4 Inch RPi LCD Hats and 3.5 Inch Pico Display
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Waveshare's small SPI LCD modules connect to Arduino, ESP32, Pico or Raspberry Pi with a handful of wires and need 3.3 V logic. The larger RPi LCD (A) and (B) boards plug straight onto the Raspberry Pi GPIO header. Check the controller chip and resolution in the title, then use the matching library.
Key specs at a glance
- Sizes
- 0.85 to 2 inch modules; 2.8, 3.2, 4 inch RPi LCDs
- Interface
- SPI (4-wire plus DC, RST and backlight)
- Panels
- IPS on most modules
- Resolution
- 128x128 up to 480x320 by model
- Logic
- 3.3 V
- Hosts
- Arduino, ESP32, Pico, Raspberry Pi
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare 128x160 General 1.8 Inch LCD Display Module₹854
Option 2Waveshare 2 Inch LCD Display Module 240x320₹1,073
Option 3Waveshare 2.8inch RPi LCD (A), 320×240₹1,581
Option 4Waveshare 3.2inch RPi LCD (B), 320x240₹2,038
Option 5Waveshare 4inch RPi LCD (A), 480x320₹3,501
Option 6Waveshare 1.47inch LCD Display Module, Rounded Corners, 172x320 Resolution, SPI Interface₹1,073
What the Waveshare SPI LCD modules and Raspberry Pi LCDs is
The small modules (0.85, 1.47, 1.69, 1.8, 1.9 and 2 inch) are SPI colour displays with rounded or square corners and a built-in driver chip, usually ST7789 or ST7735. They need a 3.3 V supply and signal levels, and there is nothing else to configure besides the pin numbers.
The RPi LCD boards (2.8, 3.2 and 4 inch) mount on the Pi's 40-pin header and often include a resistive touch controller. They use the Pi's SPI bus and need a display driver or overlay from Waveshare's wiki. A 3.5 inch Pico display is a plug-in board for the Raspberry Pi Pico.
Waveshare SPI LCD modules and Raspberry Pi LCDs pinout
The pins on the Waveshare SPI LCD modules and Raspberry Pi LCDs and what each one does.
| Pin | Function |
|---|---|
| VCC | Power, normally 3.3 V |
| GND | Ground |
| SCL / SCK | SPI clock |
| SDA / MOSI | SPI data in |
| RES | Reset |
| DC | Data or command select |
| CS | Chip select |
| BL | Backlight on, or PWM to dim |
- VCC
- Power, normally 3.3 V
- GND
- Ground
- SCL / SCK
- SPI clock
- SDA / MOSI
- SPI data in
- RES
- Reset
- DC
- Data or command select
- CS
- Chip select
- BL
- Backlight on, or PWM to dim
Wiring the Waveshare SPI LCD modules and Raspberry Pi LCDs
Module pin names vary slightly; match SCL to clock, SDA to data, and use a level shifter if the Uno drives 5 V logic.
| Waveshare SPI LCD modules and Raspberry Pi LCDs pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 3.3V (5V only if the module has a regulator) | 3V3 |
| GND | GND | GND |
| SCL / SCK | D13 | GPIO 18 |
| SDA / MOSI | D11 | GPIO 23 |
| RES / RST | D8 | GPIO 4 |
| DC | D9 | GPIO 2 |
| CS | D10 | GPIO 5 |
| BL / LED | 3.3V (or a PWM pin to dim) | 3V3 or GPIO 15 |
- VCC
- Arduino Uno:
- 3.3V (5V only if the module has a regulator)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SCL / SCK
- Arduino Uno:
- D13
- ESP32:
- GPIO 18
- SDA / MOSI
- Arduino Uno:
- D11
- ESP32:
- GPIO 23
- RES / RST
- Arduino Uno:
- D8
- ESP32:
- GPIO 4
- DC
- Arduino Uno:
- D9
- ESP32:
- GPIO 2
- CS
- Arduino Uno:
- D10
- ESP32:
- GPIO 5
- BL / LED
- Arduino Uno:
- 3.3V (or a PWM pin to dim)
- ESP32:
- 3V3 or GPIO 15
Example code
Set tft.init() to the panel's width and height from the title; use Adafruit ST7735 for 128x160 modules.
#include <Adafruit_GFX.h>
#include <Adafruit_ST7789.h>
#include <SPI.h>
#define TFT_CS 10
#define TFT_DC 9
#define TFT_RST 8
Adafruit_ST7789 tft = Adafruit_ST7789(TFT_CS, TFT_DC, TFT_RST);
void setup() {
tft.init(240, 320); // set your panel size here
tft.setRotation(1);
tft.fillScreen(ST77XX_BLACK);
tft.setTextColor(ST77XX_WHITE);
tft.setTextSize(2);
tft.setCursor(10, 10);
tft.println("Hello Geekobot");
}
void loop() {}Setup and tuning
drive the module with 3.3 V signals; an Uno needs a level shifter or resistor divider.
ST7789 modules use Adafruit_ST7789; ST7735 modules use Adafruit_ST7735; TFT_eSPI works for both.
tie BL to 3.3 V, or to a PWM pin to dim it.
copy the driver or overlay files from the product wiki, then reboot.
What you need
Shop this list13 of 14 found in our store · ₹16,351
Waveshare 128x160 General 1.8 Inch LCD Display Module: the part this guide coversWaveshare 128x160 General 1.8 Inch LCD Display Module₹854
Waveshare 2 Inch LCD Display Module 240x320: another version this guide coversWaveshare 2 Inch LCD Display Module 240x320₹1,073
Waveshare 2.8inch RPi LCD (A), 320×240: another version this guide coversWaveshare 2.8inch RPi LCD (A), 320×240₹1,581
Waveshare 3.2inch RPi LCD (B), 320x240: another version this guide coversWaveshare 3.2inch RPi LCD (B), 320x240₹2,038
Waveshare 4inch RPi LCD (A), 480x320: another version this guide coversWaveshare 4inch RPi LCD (A), 480x320₹3,501
Waveshare 1.47inch LCD Display Module, Rounded Corners, 172x320 Resolution, SPI Interface: another version this guide coversWaveshare 1.47inch LCD Display Module, Rounded Corners, 172x320 Resolution, SPI Interface₹1,073
Waveshare 1.9inch LCD Display Module, SPI Interface, IPS, 262K Colors: another version this guide coversWaveshare 1.9inch LCD Display Module, SPI Interface, IPS, 262K Colors₹1,113
Waveshare Touch LCD (D), With Touch Panel And Stand-Alone Controllers: another version this guide coversWaveshare Touch LCD (D), With Touch Panel And Stand-Alone Controllers₹1,670
Waveshare 1.69inch LCD Display Module, 240×280 Resolution, SPI Interface, IPS, 262K Colors: another version this guide coversWaveshare 1.69inch LCD Display Module, 240×280 Resolution, SPI Interface, IPS, 262K Colors₹864
Waveshare 0.85inch LCD Display Module, IPS Panel, 128×128 Resolution, SPI Interface, 65K colors: another version this guide coversWaveshare 0.85inch LCD Display Module, IPS Panel, 128×128 Resolution, SPI Interface, 65K colors₹605
Waveshare 1.69inch Round LCD Display Module with Touch panel, Micro LCD Display, 240×280 Resolution, IPS, SPI : another version this guide coversWaveshare 1.69inch Round LCD Display Module with Touch panel, Micro LCD Display, 240×280 Resolution, IPS, SPI ₹1,541- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Alternatives and when to choose them
- ST7789 displays: a closer look at the controller.
- ILI9341 TFT displays: larger SPI colour screens with touch.
- OLED displays: sharp monochrome screens.
Common mistakes to avoid
- Wiring a 3.3 V display straight to 5 V Uno pins.
- Using the wrong library for the controller chip.
- Leaving the backlight pin floating.
- Forgetting the driver or overlay for Pi hat LCDs.
Frequently asked questions
Which library do I use?
Adafruit ST7789 or ST7735, or TFT_eSPI, matching the controller chip.
Can I use these on an Uno?
Yes, with 3.3 V logic through a level shifter or resistor divider.
What is the difference between module and RPi LCD?
Modules wire to any board; RPi LCDs plug onto the Pi header.
Do they include touch?
Only the models that say Touch in the title do.
Why is the picture offset?
Set the correct width, height and offset values for the panel.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

