Comparison · Intermediate · 3 min read
Winsen Gas Sensor Modules
MOX, Catalytic and MEMS Sensors Explained
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Gas sensor modules use three main technologies. Metal-oxide sensors (MQ, MP) are cheap and sensitive but not selective. Catalytic bead sensors (MC) measure flammable gas up to the lower explosive limit. MEMS sensors (GM, MiCS) are smaller and use less power. All need warm-up time and calibration, and none of these hobby modules should be the only safety alarm for a real hazard.
Key specs at a glance
- MOX
- MP-2, MP-3B, MQ-series; analog resistance change
- Catalytic
- MC105/109/115/119; flammable gas to LEL
- MEMS
- GM402B, GM-x02B multichannel, MiCS, CMV hydrogen
- Supply
- 3 to 5 V heater supply
- Output
- Analog, digital threshold or UART
- Warm-up
- Minutes to a day for first burn-in
Technologies compared
Choose the sensor that matches the gas and the job.
| Type | Detects | Strengths | Limits |
|---|---|---|---|
| MOX (MP-2, MP-3B, MQ) | Smoke, alcohol, LPG, methane (by model) | Cheap, sensitive | Cross-sensitive; drifts; humidity effects |
| Catalytic bead (MC series) | Combustible gas up to LEL | Linear, good for flammables | Needs a bridge circuit; poisoned by silicones |
| MEMS (GM402B, Fermion MEMS) | Ethanol, H2, CH4, odour, smoke, formaldehyde | Small, low power, fast warm-up | Still cross-sensitive |
| Multichannel (Grove v2) | NO2, CO, VOCs, ethanol | Several channels on I2C | Estimates, not exact ppm |
| Figaro TGS family | Methane, LPG, hydrogen, CO | Established parts | Follow the datasheet circuit |
- MOX (MP-2, MP-3B, MQ)
- Detects:
- Smoke, alcohol, LPG, methane (by model)
- Strengths:
- Cheap, sensitive
- Limits:
- Cross-sensitive; drifts; humidity effects
- Catalytic bead (MC series)
- Detects:
- Combustible gas up to LEL
- Strengths:
- Linear, good for flammables
- Limits:
- Needs a bridge circuit; poisoned by silicones
- MEMS (GM402B, Fermion MEMS)
- Detects:
- Ethanol, H2, CH4, odour, smoke, formaldehyde
- Strengths:
- Small, low power, fast warm-up
- Limits:
- Still cross-sensitive
- Multichannel (Grove v2)
- Detects:
- NO2, CO, VOCs, ethanol
- Strengths:
- Several channels on I2C
- Limits:
- Estimates, not exact ppm
- Figaro TGS family
- Detects:
- Methane, LPG, hydrogen, CO
- Strengths:
- Established parts
- Limits:
- Follow the datasheet circuit
Using a module
1. Power the heater from the supply on the label and allow the warm-up time. 2. Read the analog output with an ADC, or use the digital pin with the potentiometer set for the threshold. 3. For bare sensors, add the load resistor from the datasheet and read the voltage across it. 4. Log values over time; trends matter more than one reading. 5. Compensate for temperature and humidity where the datasheet gives curves. Read about the older module family in MQ gas sensors.
Calibration
Burn the sensor in for the time on the datasheet. Record the reading in clean air as your baseline (R0), then use the curve to estimate concentration. For accurate values, expose the sensor to a known gas mixture. For an alarm, set a threshold slightly above the clean-air baseline and test it safely. See span gas in the electrochemical sensor guide for how professional sensors are calibrated.
Safety
Hobby modules are for monitoring and learning. They are not certified gas detectors. For LPG, CO or methane in a home or workshop, install a certified alarm, ventilate the area, keep sensors away from silicone vapour and test the alarm regularly. Never test with a naked flame.
Try it: Adc resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Reading a MOX sensor before warm-up.
- Treating cross-sensitive readings as exact ppm.
- Using a hobby module as the only gas alarm.
- Exposing catalytic sensors to silicone vapour.
- Forgetting the load resistor on a bare sensor.
Frequently asked questions
Which sensor detects LPG?
Many MOX sensors such as MQ-5 or MP-2 types respond to LPG; check the datasheet.
Can one sensor identify the gas?
No. Most sensors respond to several gases.
How long is warm-up?
From a few minutes to a day for the first burn-in.
Are MEMS sensors better than MQ?
They are smaller and use less power, but still cross-sensitive.
Can I measure ppm accurately?
Only after calibration with a known gas.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






