Component guide · Intermediate · 3 min read
300W 12A and 20A CC/CV Buck Converters

Setup, Current Limit and Cooling
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These 300 W buck converters step down 6 to 40 V or more to an adjustable output at up to 12 or 20 A. They have constant voltage (CV) and constant current (CC) trimmers, so they work as a strong bench supply, a high-power LED driver or a simple battery charger. Real continuous power depends on cooling and the input-output difference.
Key specs at a glance
- Input
- About 6 to 40 V (check board)
- Output
- About 1.2 to 36 V adjustable
- Current
- 12 A (300 W board) or 20 A peak
- Modes
- Constant voltage and constant current
- Efficiency
- Up to about 95 percent
- Cooling
- Large heatsinks, fan above about 8 A
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1High-Current Buck Converter 12A 300W₹245
Option 220A 300W Buck Converter with CC / CV₹458
What the 300W high-current buck converter is
These boards are large adjustable buck converters with two trimmers: one sets the output voltage (CV) and one sets the current limit (CC), so they act like a small bench power supply.
To set the current limit: set the voltage first with no load, then short the output through an ammeter and turn the CC trimmer to the limit you want. The charge and CC LEDs show which mode it is in.
Use thick wires and screw terminals rated for the current. Most failures at high current are hot connectors, not the converter.
300W high-current buck converter pinout
The pins on the 300W high-current buck converter and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- | Input |
| OUT+ / OUT- | Output |
| CV trimmer | Voltage |
| CC trimmer | Current limit |
| LEDs | CC mode and charge indication |
- IN+ / IN-
- Input
- OUT+ / OUT-
- Output
- CV trimmer
- Voltage
- CC trimmer
- Current limit
- LEDs
- CC mode and charge indication
Wiring the 300W high-current buck converter
Set the output with a multimeter before connecting any load. Turn the trimmer slowly; many need 10 or more turns before the voltage moves.
| 300W high-current buck converter pin | LED / charger use | Bench supply use |
|---|---|---|
| IN | 12 to 36 V supply | Same |
| OUT | LED string or battery | Load |
- IN
- LED / charger use:
- 12 to 36 V supply
- Bench supply use:
- Same
- OUT
- LED / charger use:
- LED string or battery
- Bench supply use:
- Load
Example code
A minimal sketch to check the part works.
1. Power the module with nothing on the output.
2. Measure OUT+ to OUT- with a multimeter.
3. Turn the trimmer until the reading is correct.
4. Connect the load and measure again under load.Setup and tuning
with no load, set the output voltage with a meter.
short the output through the meter on its 10 A range and set the current limit, or set it with a dummy load.
set CV to the full-charge voltage and CC to the safe charge current; lithium packs still need a BMS and should not be left unattended.
set CC to the LED string's rated current and CV a little above its voltage.
add a 12 V fan for long runs above about 8 A, and use wires rated for the current.
What you need
Shop this list5 of 5 found in our store · ₹1,427
High-Current Buck Converter 12A 300W: the part this guide coversHigh-Current Buck Converter 12A 300W₹245
20A 300W Buck Converter with CC / CV: another version this guide covers20A 300W Buck Converter with CC / CV₹458
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
SMPS power supply in metal enclosure (5/12/24 V): a bench input supplySMPS Power Supply, Metal Enclosure (5V / 12V / 24V)₹298Closest match, check the specs
INA219 current and power monitor module: to log voltage and current from the outputINA219 Current and Power Monitor Module₹249
Alternatives and when to choose them
- XL4005 buck: lower current.
- Bench power supply: metered and protected.
- Robot power planning.
Common mistakes to avoid
- Using thin wires at high current, which heat up and drop voltage.
- Charging lithium packs without a BMS.
- Running above 8 A for long periods with no fan.
- Setting the current limit higher than the load or battery can safely take.
Frequently asked questions
Can this buck converter charge a 12 V lead-acid battery?
Yes. Set CV to about 13.8 V for float or up to 14.4 V for a cycle charge, and set CC to about a tenth of the battery's Ah rating.
What is the real continuous current?
About 8 to 10 A without a fan. The 12 A and 20 A figures need strong airflow.
Can it drive high-power LEDs at constant current?
Yes. That is what the CC trimmer is for: the output drops its voltage to hold the set current.
Is it protected against reverse polarity?
Usually not. Check the input polarity carefully or add protection.
Can it turn 24 V into 12 V?
Yes. Inputs from about 6 to 40 V are accepted, and the output must be a few volts below the input.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
