Buying guide · Beginner · 3 min read
Bench Power Supplies
CV, CC and Choosing One
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A bench power supply gives an adjustable, current-limited voltage. In constant-voltage mode it holds the voltage you set; if the circuit tries to draw more than your current limit, it switches to constant-current mode and lowers the voltage, so a wiring mistake does not burn parts. A 0 to 30 V, 0 to 5 A unit covers most hobby work. Linear supplies are quieter; switching supplies are lighter and cheaper.
Key specs at a glance
- Typical range
- 0 to 30 V, 0 to 5 A (single channel)
- Modes
- CV (constant voltage) and CC (constant current)
- Linear
- Low ripple and noise, heavy, runs warm
- Switching
- Light, efficient, slightly more noise
- Useful extras
- Output on/off button, memory presets, 3-digit or better display
- DC-DC module type
- Panel modules powered by a laptop adapter or SMPS
CV and CC in plain words
Set the voltage to what your circuit needs, say 5 V, and the current limit a little above what it should draw, say 300 mA. If everything is fine, the supply stays in CV and the current display shows the real draw. If there is a short or a backwards part, the current hits 300 mA and the supply switches to CC: the voltage drops and the CC light comes on. You have lost nothing.
That is why a bench supply is the safest way to power a new circuit for the first time, far safer than a battery pack or a USB charger.
Choosing one
| Type | Pros | Cons | Good for |
|---|---|---|---|
| 30 V 5 A switching (single) | Light, affordable, plenty of current | Some fan and output noise | General hobby use, motors, LED strips |
| Linear (30 V 3 A) | Very clean output | Heavy, hot at low voltage and high current | Audio and analog circuits |
| Programmable DC-DC module | Compact, USB or Wi-Fi control | Needs a separate 36 to 60 V input supply | Tight benches, automation |
| Dual or triple channel | Positive and negative rails, tracking | Costs more | Op-amp circuits needing ±12 V |
- 30 V 5 A switching (single)
- Pros:
- Light, affordable, plenty of current
- Cons:
- Some fan and output noise
- Good for:
- General hobby use, motors, LED strips
- Linear (30 V 3 A)
- Pros:
- Very clean output
- Cons:
- Heavy, hot at low voltage and high current
- Good for:
- Audio and analog circuits
- Programmable DC-DC module
- Pros:
- Compact, USB or Wi-Fi control
- Cons:
- Needs a separate 36 to 60 V input supply
- Good for:
- Tight benches, automation
- Dual or triple channel
- Pros:
- Positive and negative rails, tracking
- Cons:
- Costs more
- Good for:
- Op-amp circuits needing ±12 V
Safe habits
- 1Set the voltage and current limit with the output off, before connecting the circuit.
- 2Start with a low current limit and raise it only as needed.
- 3Watch for voltage overshoot: switch the output on with the circuit connected only if your supply does not spike at turn-on.
- 4Do not connect a supply to a battery without care: if the supply is off, some units let the battery discharge back into them. For lithium cells use a proper charger.
- 5Use thick, short leads for high currents, and measure the voltage at the load with a multimeter.
Try it: Power supply sizing calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Leaving the current limit at maximum.
- Adjusting the voltage with the circuit connected.
- Charging lithium cells straight from a bench supply without a charger.
- Thin, long leads that drop voltage at high current.
- Ignoring the CC light when it comes on.
Frequently asked questions
What does CC mean on a power supply?
Constant current: the circuit tried to draw more than your current limit, so the supply is holding the current and lowering the voltage.
Is a 30 V 5 A power supply enough?
Yes, for almost all hobby electronics, Arduino projects, small motors and LED strips.
Linear or switching bench supply?
Linear for low-noise audio and analog work; switching for lighter weight and more current at lower cost.
How do I set the current limit?
With the output off, turn the current knob to the limit you want. Some supplies need the leads briefly shorted to set it; check the manual.
Can I use a bench power supply instead of batteries?
Yes, and it is safer for testing because the current limit protects against mistakes.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- Bench power supply operating manuals (CV/CC operation)
- Keysight power supply fundamentals application note
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


