How-to · Beginner · 3 min read
How to Use a Multimeter
Voltage, Current, Resistance and Continuity
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
To measure voltage, set the multimeter to V DC, plug the red lead into the V/Ω jack and the black into COM, then touch the leads across the part. To measure current, move the red lead to the A or mA jack and put the meter in series with the circuit. Measure resistance and continuity only with the power off.
Key specs at a glance
- Voltage
- Measured in parallel (across a part)
- Current
- Measured in series (circuit broken and meter inserted)
- Resistance / continuity
- Power must be off
- Jacks
- COM (black), V/Ω/mA (red), 10 A or 20 A (red, high current)
- Safety rating
- CAT II for household sockets, CAT III for distribution boards
- Useful extras
- Auto-range, true RMS, capacitance, frequency, temperature
How to measure DC voltage
- 1Turn the dial to V⎓ (DC volts). On a manual-range meter, choose the range just above the expected voltage, such as 20 V for a 12 V battery.
- 2Black lead in COM, red lead in VΩ.
- 3Touch black to ground (-) and red to the point you are measuring.
- 4A minus sign means the leads are reversed; no harm done.
How to measure current
- 1Turn the circuit off.
- 2Move the red lead to the mA jack (under about 200 mA) or the 10A jack (higher currents). Start with 10A if unsure.
- 3Set the dial to A⎓ or mA⎓.
- 4Break the circuit and connect the meter in series so all current flows through it.
- 5Power on, read, power off, and move the red lead back to VΩ immediately afterwards.
Measuring voltage with the leads still in the current jack short-circuits the source and usually blows the meter's fuse.
Resistance, continuity and diode tests
power off; touch the leads across the part. Measuring a resistor still in a circuit can give a lower reading because of parallel paths.
the meter beeps when there is a near-zero resistance path. Use it to find broken wires, check solder joints and trace breadboard rows.
shows the forward voltage of a diode or LED (about 0.6 V for silicon, 1.8 to 3 V for LEDs) in one direction and OL in the other.
Multimeter safety
Check the CAT rating printed near the jacks: CAT II 600 V is the minimum for 230 V household sockets, CAT III for distribution boards. Use leads with finger guards, keep one hand away from the circuit when probing mains, and never measure current directly across a supply. If you are unsure about a mains measurement, do not make it.
How to choose a multimeter
| User | Look for |
|---|---|
| Student / beginner | Auto-range, continuity beep, fused current inputs, CAT II rating |
| Maker / hobbyist | Add capacitance, frequency, temperature probe, backlight, 6000-count display |
| Technician / electrician | True RMS, CAT III or CAT IV rating, robust case, low-impedance (LoZ) mode, clamp meter for AC current |
- Student / beginner
- Auto-range, continuity beep, fused current inputs, CAT II rating
- Maker / hobbyist
- Add capacitance, frequency, temperature probe, backlight, 6000-count display
- Technician / electrician
- True RMS, CAT III or CAT IV rating, robust case, low-impedance (LoZ) mode, clamp meter for AC current
Try it: Ohm's law calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Leaving the red lead in the A jack and then measuring voltage, which shorts the circuit.
- Measuring resistance with the circuit powered.
- Trying to measure current in parallel like voltage.
- Using a cheap meter with no CAT rating on mains.
- Forgetting to switch off, which drains the meter's battery.
Frequently asked questions
How do I check a battery with a multimeter?
Set V DC, touch red to + and black to -. A fresh AA reads about 1.5 to 1.6 V, a full Li-ion cell about 4.2 V, and an empty one about 3.0 V.
How do I test continuity?
Turn the power off, select the continuity (beep) mode and touch the two ends of the wire or joint. A beep means they are connected.
Why does my multimeter show 0 when measuring current?
The current fuse may be blown, the red lead may be in the wrong jack, or the meter is in parallel instead of series.
What does OL mean on a multimeter?
Overload or open loop: the value is beyond the selected range, or there is no connection, as in an open circuit or a reversed diode.
Do I need a true RMS multimeter?
Only for measuring non-sinusoidal AC, such as inverter outputs or variable-speed drives. For DC electronics work, a standard meter is fine.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- IEC 61010-1 safety requirements for electrical equipment for measurement
- Fluke ABCs of multimeter safety (Fluke Corporation)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


