Component guide · Beginner · 4 min read
Li-ion, 18650 and LiPo Batteries
Charging, BMS and Safety
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Lithium-ion cells, including 18650s and flat LiPo packs, store about 3.6 to 3.7 V nominal, charge to exactly 4.2 V and should not be discharged below about 3.0 V. Charge a single cell with a constant-current, constant-voltage charger such as the TP4056 module, and use a BMS for packs of cells in series. Damaged or overcharged cells can catch fire.
Key specs at a glance
- Nominal voltage
- 3.6 to 3.7 V per cell
- Full charge
- 4.20 V per cell (±50 mV)
- Cut-off
- About 2.5 to 3.0 V per cell (check the datasheet)
- Genuine 18650 capacity
- About 2000 to 3500 mAh
- TP4056 module
- 5 V input, 1 A CC/CV charge to 4.2 V, protection on DW01A versions
- Series packs
- 2S = 7.4 V, 3S = 11.1 V nominal; need a balancing BMS
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
18650 vs LiPo vs Li-ion pouch: what's the difference?
| Type | Shape | Strength | Typical use |
|---|---|---|---|
| 18650 Li-ion | Cylinder 18 x 65 mm, steel can | Robust, high energy, cheap per Wh | Power banks, robots, torches, packs |
| 21700 Li-ion | Cylinder 21 x 70 mm | More capacity and current than 18650 | Larger packs, e-bikes |
| LiPo pouch | Flat, soft foil | Thin and light, high discharge (C) ratings | Drones, wearables, slim gadgets |
| LiFePO4 | Cylinder or prismatic | Safer, long life, 3.2 V nominal (3.65 V full) | Solar storage, UPS |
- 18650 Li-ion
- Shape:
- Cylinder 18 x 65 mm, steel can
- Strength:
- Robust, high energy, cheap per Wh
- Typical use:
- Power banks, robots, torches, packs
- 21700 Li-ion
- Shape:
- Cylinder 21 x 70 mm
- Strength:
- More capacity and current than 18650
- Typical use:
- Larger packs, e-bikes
- LiPo pouch
- Shape:
- Flat, soft foil
- Strength:
- Thin and light, high discharge (C) ratings
- Typical use:
- Drones, wearables, slim gadgets
- LiFePO4
- Shape:
- Cylinder or prismatic
- Strength:
- Safer, long life, 3.2 V nominal (3.65 V full)
- Typical use:
- Solar storage, UPS
How to judge capacity (and spot fake cells)
A genuine 18650 holds about 2000 to 3500 mAh and weighs about 42 to 50 g. Labels claiming 6000 to 9900 mAh are fake; such cells are often re-wrapped low-grade cells weighing under 30 g. Buy branded cells from traceable sources and check weight.
Runtime estimate: hours = capacity (mAh) x 0.8 / average current (mA). A 2600 mAh cell running an ESP32 that averages 80 mA lasts about 26 hours; with deep sleep it can last months.
Charging a single cell with a TP4056 module
- 1Use the version with two extra chips (DW01A and FS8205A); it adds over-discharge, overcharge and short-circuit protection.
- 2Connect the cell to B+ and B-.
- 3Connect your project to OUT+ and OUT-, not B+/B-, so the protection works.
- 4Supply 5 V through the USB port or IN+/IN-. The red LED shows charging; blue or green means full.
- 5The charge current is set by the RPROG resistor: 1.2 kΩ gives 1 A. For small LiPo cells under 1000 mAh, replace it with a larger value (for example 2.4 kΩ for about 500 mA) to stay at or below 1C.
A TP4056 charges one cell, or several in parallel, never cells in series.
Series packs and BMS boards
Connecting cells in series raises voltage: 2S = 7.4 V nominal (8.4 V full), 3S = 11.1 V (12.6 V full), 4S = 14.8 V (16.8 V full). A BMS (battery management system) board for the right series count protects each cell from over-charge and over-discharge, limits current, and on balancing versions equalises cell voltages. Charge series packs with a charger set to the pack's full voltage, connected through the BMS.
Powering an ESP32 or Arduino from a Li-ion cell
use a low-dropout regulator such as the ME6211, HT7333 or MCP1700 between the cell and 3V3. The AMS1117 found on many dev boards needs over 4.3 V, so it drops out early.
use a boost converter to 5 V, or a 2S pack into VIN.
VSYS accepts 1.8 to 5.5 V directly from a single cell.
Lithium battery safety rules
- Never charge above 4.2 V per cell, below 0 °C, or unattended on flammable surfaces.
- Do not use cells that are swollen, dented, hot or have torn wraps.
- Never short a cell; an 18650 can deliver tens of amps into a short.
- Store at about 3.7 to 3.8 V in a cool place, and insulate terminals.
- Use battery holders or spot-welded nickel strip; do not solder directly to cells, as the heat damages them.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Wiring a project to B+ and B- on a TP4056 board, bypassing protection.
- Charging series cells with a single-cell charger.
- Buying cells by the mAh number on the label rather than brand and weight.
- Running a 3.3 V board through an AMS1117 from one cell, which browns out as the cell drops.
- Charging small LiPo pouches at 1 A, which is above 1C and stresses the cell.
Frequently asked questions
What is the voltage of an 18650 battery?
3.6 to 3.7 V nominal, 4.2 V when fully charged, and about 2.5 to 3.0 V when empty. Most of its energy is delivered between 4.1 and 3.4 V.
Is a LiPo battery the same as Li-ion?
Both use lithium-ion chemistry and the same 4.2 V full-charge voltage. LiPo usually describes flat pouch cells with a polymer electrolyte and higher discharge ratings; 18650s are cylindrical cells in steel cans.
Can a TP4056 charge two batteries?
Only two or more in parallel, which behaves like one bigger 3.7 V cell. It cannot charge cells wired in series.
Do I need a BMS for a single 18650?
A protected cell or a TP4056 board with DW01A protection is enough. For two or more cells in series, use a BMS rated for that series count and current.
How long will an 18650 power my project?
Roughly the capacity in mAh x 0.8 divided by the average current in mA. A 2600 mAh cell at 100 mA gives about 20 hours. Deep sleep and efficient regulators extend this dramatically.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 65 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- TP4056 standalone linear Li-ion charger datasheet (NanJing Top Power)
- DW01A battery protection IC datasheet (Fortune Semiconductor)
- Samsung INR18650-25R and LG/Molicel 18650 cell datasheets
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




