LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA popular assistive-technology project. The ultrasonic sensor looks ahead from the cane, and a vibration motor in the handle pulses faster as an obstacle approaches, turning continuous within 40 cm. A buzzer adds a sound cue at close range.
This is a learning prototype. It does not replace a white cane or mobility training.
Tick anything you already have and the total updates.
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
smart_cane.inoVerify & upload in Electrolark// Ultrasonic smart cane
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "smart-cane"
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 3;
const uint8_t VIBE_PIN = 4;
const uint8_t BUZZER_PIN = 5;
// ---- latest readings ----
float distCm = 0;
const int ALERT_CM = 120; // start buzzing within 1.2 m
const int CLOSE_CM = 40; // continuous buzz
unsigned long lastPulse = 0;
bool pulseOn = false;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setVibe(bool on) { digitalWrite(VIBE_PIN, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
pinMode(VIBE_PIN, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
distCm = readDistanceCm();
if (distCm < 0 || distCm > ALERT_CM) { setVibe(false); setBuzzer(false); delay(60); return; }
if (distCm <= CLOSE_CM) { setVibe(true); setBuzzer(true); delay(60); return; }
unsigned long gap = map((long)distCm, CLOSE_CM, ALERT_CM, 80, 700); // closer = faster pulses
if (millis() - lastPulse > gap) { lastPulse = millis(); pulseOn = !pulseOn; setVibe(pulseOn); setBuzzer(false); }
delay(30);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Check the transistor orientation (flat face: C-B-E for BC547).
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
12 parts: Nano CH340 Development Board (Soldered), HC-SR04 Ultrasonic Range Finder Sensor Module, Coin Vibration Motor 3V, Active Buzzer Module 3.3–5V, General Purpose Transistors (Pack), Diodes (Pack of 10, 1N4007), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, MT3608 Mini Boost Converter Module, TP4056 1A Li-ion Charger Module with Protection, plus 2 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (smart_cane.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹671 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Time-of-flight measurement with sound; Transistors as switches.
This is a learning prototype. It does not replace a white cane or mobility training.
Ideas that reuse this build: Parking sensor with lights. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.