Component guide · Beginner · 4 min read
Diodes Explained
1N4007, 1N4148, 1N5819 Schottky and Zener
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A diode lets current flow one way, from anode to cathode (the striped end), and blocks it the other way, dropping about 0.7 V in silicon types and 0.3 V in Schottky types. Use a 1N4007 for mains-frequency rectifying and relay flyback protection, a 1N4148 for fast low-current signals, a 1N5819 Schottky for low-loss reverse-polarity protection, and a Zener (reverse-biased) to clamp or regulate a voltage.
Key specs at a glance
- 1N4007
- 1000 V, 1 A, slow (general rectifier), Vf about 0.7 to 1 V
- 1N4148
- 100 V, 200 mA, fast (4 ns) signal diode
- 1N5819
- 40 V, 1 A Schottky, Vf about 0.3 to 0.45 V
- 1N5822
- 40 V, 3 A Schottky
- Zener (e.g. 1N4733A 5.1 V)
- Regulates/clamps at its Zener voltage when reverse biased
- Polarity
- Stripe = cathode; current flows from anode to cathode
How a diode works
A diode is a one-way valve. Apply a positive voltage to the anode relative to the cathode (forward bias) and, once the voltage exceeds the forward voltage (about 0.7 V for silicon), it conducts freely. Reverse the voltage and it blocks, up to its rated reverse voltage, beyond which it breaks down. Zener diodes are designed to break down cleanly at a known voltage, which makes them useful as simple regulators and protectors. An LED is a diode too; see LEDs.
Which diode do I need?
| Diode | Type | Max reverse V | Current | Forward drop | Use it for |
|---|---|---|---|---|---|
| 1N4001 to 1N4007 | Rectifier | 50 to 1000 V | 1 A | About 0.7 to 1 V | Mains rectifiers, relay/solenoid flyback, reverse protection where 0.7 V loss is fine |
| 1N5400 to 1N5408 | Rectifier | 50 to 1000 V | 3 A | About 0.9 V | Higher-current supplies |
| 1N4148 | Signal | 100 V | 200 mA | 0.7 V | Logic, fast switching, small flyback on signal relays |
| 1N5819 / 1N5822 | Schottky | 40 V | 1 A / 3 A | 0.3 to 0.45 V | Reverse-polarity protection, PWM motor flyback, OR-ing supplies |
| SS34 (SMD) | Schottky | 40 V | 3 A | 0.5 V | Buck/boost converters |
| 1N47xx series | Zener | Zener voltage 3.3 to 33 V | 1 W | 0.7 V forward | Voltage clamps, cheap references, over-voltage protection |
| Bridge rectifier (e.g. KBP, DB107) | 4 diodes | up to 1000 V | 1 to 50 A | About 1.4 V (two drops) | AC to DC conversion |
- 1N4001 to 1N4007
- Type:
- Rectifier
- Max reverse V:
- 50 to 1000 V
- Current:
- 1 A
- Forward drop:
- About 0.7 to 1 V
- Use it for:
- Mains rectifiers, relay/solenoid flyback, reverse protection where 0.7 V loss is fine
- 1N5400 to 1N5408
- Type:
- Rectifier
- Max reverse V:
- 50 to 1000 V
- Current:
- 3 A
- Forward drop:
- About 0.9 V
- Use it for:
- Higher-current supplies
- 1N4148
- Type:
- Signal
- Max reverse V:
- 100 V
- Current:
- 200 mA
- Forward drop:
- 0.7 V
- Use it for:
- Logic, fast switching, small flyback on signal relays
- 1N5819 / 1N5822
- Type:
- Schottky
- Max reverse V:
- 40 V
- Current:
- 1 A / 3 A
- Forward drop:
- 0.3 to 0.45 V
- Use it for:
- Reverse-polarity protection, PWM motor flyback, OR-ing supplies
- SS34 (SMD)
- Type:
- Schottky
- Max reverse V:
- 40 V
- Current:
- 3 A
- Forward drop:
- 0.5 V
- Use it for:
- Buck/boost converters
- 1N47xx series
- Type:
- Zener
- Max reverse V:
- Zener voltage 3.3 to 33 V
- Current:
- 1 W
- Forward drop:
- 0.7 V forward
- Use it for:
- Voltage clamps, cheap references, over-voltage protection
- Bridge rectifier (e.g. KBP, DB107)
- Type:
- 4 diodes
- Max reverse V:
- up to 1000 V
- Current:
- 1 to 50 A
- Forward drop:
- About 1.4 V (two drops)
- Use it for:
- AC to DC conversion
Four everyday uses
- 1Reverse-polarity protection: a Schottky diode in series with the supply input means a reversed battery does nothing instead of destroying the board. It costs 0.3 V; a P-channel MOSFET avoids even that.
- 2Flyback protection: across every relay coil, solenoid and DC motor, cathode to the positive supply. A 1N4007 suits relays; a Schottky suits PWM-driven motors. See transistors and MOSFETs.
- 3Rectifying AC: four diodes as a bridge turn a transformer's AC into pulsing DC, smoothed by a large capacitor.
- 4Clamping and simple regulation: a 5.1 V Zener with a series resistor protects a 5 V input, or provides a reference for a comparator.
Using a Zener diode
Connect the Zener reverse-biased (cathode to the positive side) across the load, with a series resistor from the supply. The resistor must pass the load current plus a few milliamps for the Zener: R = (Vin - Vz) / (Iload + Iz). For a 12 V supply, 5.1 V Zener and 10 mA load with 5 mA for the Zener: (12 - 5.1) / 0.015 = 460 Ω, so 470 Ω, dissipating about 0.1 W. Zener regulators waste power and drift with current, so use them for tiny loads and protection, and a regulator for real supplies.
Testing a diode with a multimeter
Set the meter to diode test. Red lead on the anode, black on the cathode (stripe): a good silicon diode shows about 0.5 to 0.7 V, a Schottky about 0.2 to 0.4 V. Reverse the leads: it should read OL. A reading near 0 V both ways means it is shorted; OL both ways means it is open. See how to use a multimeter.
Try it: Zener resistor calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Fitting a flyback diode backwards, which shorts the supply through the transistor the moment it turns on.
- Using a slow 1N4007 as a flyback diode on a fast PWM motor; use a Schottky.
- Exceeding a Schottky's 40 V reverse rating on a 48 V system.
- Forgetting the Zener's series resistor.
- Expecting a Zener to regulate a load of hundreds of milliamps.
Frequently asked questions
Which way round does a diode go?
The stripe marks the cathode. Conventional current flows into the unmarked end (anode) and out of the striped end (cathode). For flyback protection, the stripe faces the positive supply.
What is the difference between 1N4007 and 1N4148?
The 1N4007 handles 1 A and 1000 V but switches slowly, so it suits power and mains-frequency jobs. The 1N4148 handles only 200 mA but switches in nanoseconds, so it suits signals and logic.
What is a Schottky diode used for?
Anywhere the 0.7 V drop of a normal diode is too much: reverse-polarity protection on low-voltage boards, flyback on PWM motors, solar panel blocking, and inside switching converters.
Can I use any diode as a flyback diode?
For relays and solenoids a 1N4007 or 1N4148 is fine. For PWM-driven motors use a fast Schottky rated above the motor current.
How does a Zener diode regulate voltage?
Reverse-biased, it conducts once the voltage reaches its Zener value and holds it there, with a series resistor limiting the current. It works for small loads and as a protective clamp.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 21 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- 1N4001 to 1N4007 datasheet (onsemi / Vishay)
- 1N4148 datasheet (Vishay)
- 1N5819 datasheet (onsemi)
- 1N4728A to 1N4764A Zener datasheet (onsemi)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


