Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsType the code and press # to unlock; * clears. Three wrong codes lock the keypad for 30 seconds. The relay switches a 12 V solenoid bolt that suits cabinets, lockers and workshop doors.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
16-key membrane keypad scanned as a 4×4 grid, so 8 wires read 16 buttons.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
12 V + → relay COM, relay NO → solenoid +, solenoid − → 12 V −. Fit a 1N4007 across the solenoid, stripe to +.
keypad_door_lock.inoVerify & upload in Electrolark// Keypad code door lock
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "keypad-door-lock"
#include <Keypad.h>
// ---- pins ----
const uint8_t KP_R1 = 2;
const uint8_t KP_R2 = 3;
const uint8_t KP_R3 = 4;
const uint8_t KP_R4 = 5;
const uint8_t KP_C1 = 6;
const uint8_t KP_C2 = 7;
const uint8_t KP_C3 = 8;
const uint8_t KP_C4 = 12;
const uint8_t RELAY_PIN = 13;
const uint8_t BUZZER_PIN = 9;
const char KEYS[4][4] = {{'1','2','3','A'},{'4','5','6','B'},{'7','8','9','C'},{'*','0','#','D'}};
byte rowPins[4] = {KP_R1, KP_R2, KP_R3, KP_R4};
byte colPins[4] = {KP_C1, KP_C2, KP_C3, KP_C4};
Keypad keypad = Keypad(makeKeymap(KEYS), rowPins, colPins, 4, 4);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
const char PIN_CODE[] = "2580"; // change me
const unsigned long UNLOCK_MS = 5000;
const int MAX_TRIES = 3;
const unsigned long LOCKOUT_MS = 30000;
char entered[9];
byte len = 0;
int wrongTries = 0;
unsigned long lockedOutUntil = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void beep(int ms) { setBuzzer(true); delay(ms); setBuzzer(false); }
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
Serial.println(F("Enter code, then #. * clears."));
}
void loop() {
char k = keypad.getKey();
if (!k) return;
if (millis() < lockedOutUntil) { beep(400); return; }
beep(30);
if (k == '*') { len = 0; Serial.println(F("cleared")); return; }
if (k != '#') {
if (len < sizeof(entered) - 1) entered[len++] = k;
Serial.print('*');
return;
}
entered[len] = 0;
Serial.println();
if (strcmp(entered, PIN_CODE) == 0) {
Serial.println(F("Unlocked"));
wrongTries = 0;
setRelay(true); // relay powers the 12 V solenoid
delay(UNLOCK_MS);
setRelay(false);
} else {
Serial.println(F("Wrong code"));
beep(600);
if (++wrongTries >= MAX_TRIES) { lockedOutUntil = millis() + LOCKOUT_MS; wrongTries = 0; Serial.println(F("Locked out for 30 s")); }
}
len = 0;
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Rows and columns are swapped or reversed; swap the rowPins and colPins lists.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Membrane Matrix Keypad (4x4), 5V Relay Module with Optocoupler (1 channel), Active Buzzer Module 3.3–5V, 12V Electric Solenoid Door / Cabinet Lock, DC Power Adapter 12V 2A (5.5x2.1mm), Diodes (Pack of 10, 1N4007), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (keypad_door_lock.ino). Install this library first: Keypad.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,062 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Isolation, relays and switching higher-power loads; Matrix scanning.
Ideas that reuse this build: RFID card version. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Enter code, then #. * clears.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.