Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsThe TTP223 pad senses your finger through a few millimetres of wood, plastic or glass. Each tap flips the relay, so a 12 V desk lamp toggles on and off with no visible switch.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Capacitive touch pad: works through thin plastic, glass or wood, so you can hide it inside an enclosure.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
touch_lamp_switch.inoVerify & upload in Electrolark// Touch lamp switch
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "touch-lamp-switch"
// ---- pins ----
const uint8_t TOUCH_PIN = 2;
const uint8_t RELAY_PIN = 3;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
bool touched = false;
bool relayOn = false;
bool lastInput = false;
unsigned long lastToggle = 0;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(TOUCH_PIN, INPUT);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
bool input = digitalRead(TOUCH_PIN) == HIGH;
if (input && !lastInput && millis() - lastToggle > 400) {
relayOn = !relayOn;
lastToggle = millis();
setRelay(relayOn);
Serial.println(relayOn ? F("Lamp ON") : F("Lamp OFF"));
}
lastInput = input;
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Ground the enclosure or keep long wires away from the pad.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Capacitive Touch Sensor Module (TTP223), 5V Relay Module with Optocoupler (1 channel), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (touch_lamp_switch.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹544 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Capacitive sensing; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Double-clap to switch instead. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Enter the PIN and a 12 V solenoid bolt pulls back for five seconds.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.