Component guide · Beginner · 5 min read
Arduino Uno

Pinout, Specs and Getting Started
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The Arduino Uno is a beginner-friendly microcontroller board that reads sensors and controls LEDs, motors and relays using simple C++ programs called sketches. The classic Uno R3 runs an ATmega328P at 16 MHz with 14 digital pins, 6 analog inputs and 5 V logic. The newer Uno R4 keeps the same layout with a faster 48 MHz chip.
Key specs at a glance
- Microcontroller
- ATmega328P (R3) / Renesas RA4M1 (R4)
- Clock
- 16 MHz (R3) / 48 MHz (R4)
- Logic level
- 5 V
- Digital I/O
- 14 pins, 6 with PWM (3, 5, 6, 9, 10, 11)
- Analog inputs
- 6 (A0 to A5), 10-bit on R3, up to 14-bit on R4
- Flash / RAM
- 32 KB / 2 KB (R3); 256 KB / 32 KB (R4)
- Power input
- USB 5 V, or 7 to 12 V on the barrel jack (R4 accepts up to 24 V)
- Pin current
- 20 mA recommended per pin on R3; 8 mA on R4
What is an Arduino Uno?
An Arduino Uno is a small circuit board built around a microcontroller: a single chip that contains a processor, memory and input/output pins. You write a program on your computer in the free Arduino IDE, upload it over USB, and the board runs it on its own every time it is powered.
The Uno is the most common starting point because its headers match thousands of add-on shields, almost every tutorial is written for it, and its 5 V pins work directly with classic hobby modules such as the HC-SR04 ultrasonic sensor, 16x2 LCDs and relay modules.
Arduino Uno pinout explained
The pin layout is the same on the R3 and R4, so shields and wiring diagrams carry over.
| Pin(s) | What it does | Notes |
|---|---|---|
| D0, D1 | Serial RX / TX | Shared with USB. Leave free while uploading. |
| D2, D3 | Digital I/O with external interrupts | Use for buttons, encoders and pulse sensors. |
| D3, D5, D6, D9, D10, D11 | PWM output (~) | Dim LEDs, set motor speed, drive servos. |
| D10 to D13 | SPI (SS, MOSI, MISO, SCK) | D13 also drives the onboard LED. |
| A0 to A5 | Analog inputs | Also usable as digital pins. A4 = SDA, A5 = SCL for I2C. |
| 5V, 3.3V, GND | Power out | 3.3 V pin supplies only about 50 mA on the R3. |
| VIN | Raw input power | Connects to the barrel-jack voltage. |
| RESET | Restarts the sketch | Pull low to reset. |
- D0, D1
- What it does:
- Serial RX / TX
- Notes:
- Shared with USB. Leave free while uploading.
- D2, D3
- What it does:
- Digital I/O with external interrupts
- Notes:
- Use for buttons, encoders and pulse sensors.
- D3, D5, D6, D9, D10, D11
- What it does:
- PWM output (~)
- Notes:
- Dim LEDs, set motor speed, drive servos.
- D10 to D13
- What it does:
- SPI (SS, MOSI, MISO, SCK)
- Notes:
- D13 also drives the onboard LED.
- A0 to A5
- What it does:
- Analog inputs
- Notes:
- Also usable as digital pins. A4 = SDA, A5 = SCL for I2C.
- 5V, 3.3V, GND
- What it does:
- Power out
- Notes:
- 3.3 V pin supplies only about 50 mA on the R3.
- VIN
- What it does:
- Raw input power
- Notes:
- Connects to the barrel-jack voltage.
- RESET
- What it does:
- Restarts the sketch
- Notes:
- Pull low to reset.
Uno R3 vs Uno R4: which should you buy?
Buy the R3 (or a compatible clone) when you are following older tutorials, need the cheapest board, or use libraries that talk directly to ATmega registers. Buy the R4 Minima for more memory, a 12-bit DAC, a 24 V input range and a USB-C port. Buy the R4 WiFi when the project needs Wi-Fi or Bluetooth, or you like the built-in 12x8 LED matrix.
One catch on the R4: each pin is rated for only 8 mA, so an LED that was fine on an R3 should get a larger resistor, and anything heavier needs a transistor or MOSFET.
| Feature | Uno R3 | Uno R4 Minima | Uno R4 WiFi |
|---|---|---|---|
| Chip | ATmega328P, 8-bit | RA4M1, 32-bit Arm Cortex-M4 | RA4M1 + ESP32-S3 |
| Clock | 16 MHz | 48 MHz | 48 MHz |
| Flash / RAM | 32 KB / 2 KB | 256 KB / 32 KB | 256 KB / 32 KB |
| USB | USB-B | USB-C | USB-C |
| Wireless | None | None | Wi-Fi + Bluetooth LE |
| Max pin current | 20 mA (40 mA absolute) | 8 mA | 8 mA |
- Chip
- Uno R3:
- ATmega328P, 8-bit
- Uno R4 Minima:
- RA4M1, 32-bit Arm Cortex-M4
- Uno R4 WiFi:
- RA4M1 + ESP32-S3
- Clock
- Uno R3:
- 16 MHz
- Uno R4 Minima:
- 48 MHz
- Uno R4 WiFi:
- 48 MHz
- Flash / RAM
- Uno R3:
- 32 KB / 2 KB
- Uno R4 Minima:
- 256 KB / 32 KB
- Uno R4 WiFi:
- 256 KB / 32 KB
- USB
- Uno R3:
- USB-B
- Uno R4 Minima:
- USB-C
- Uno R4 WiFi:
- USB-C
- Wireless
- Uno R3:
- None
- Uno R4 Minima:
- None
- Uno R4 WiFi:
- Wi-Fi + Bluetooth LE
- Max pin current
- Uno R3:
- 20 mA (40 mA absolute)
- Uno R4 Minima:
- 8 mA
- Uno R4 WiFi:
- 8 mA
Upload your first sketch
Install the Arduino IDE from arduino.cc, plug in the board, choose Tools > Board > Arduino Uno (or Uno R4) and pick the right port. Clone boards that use a CH340 USB chip may need the CH340 driver on Windows. Then upload this blink sketch:
void setup() {
pinMode(LED_BUILTIN, OUTPUT); // pin 13 on the Uno
}
void loop() {
digitalWrite(LED_BUILTIN, HIGH);
delay(500);
digitalWrite(LED_BUILTIN, LOW);
delay(500);
}How to power an Arduino Uno safely
simplest for the bench. A computer port supplies 500 mA.
the onboard regulator turns this into 5 V. Above 12 V it runs hot.
only feed a clean, regulated 5 V here. It bypasses the regulator and protection.
should never draw from the Uno's 5 V pin. Give them their own supply and connect the grounds together.
Arduino Uno vs ESP32 vs Raspberry Pi Pico
Choose the Uno for learning and for 5 V modules; the ESP32 for Wi-Fi and Bluetooth projects; the Raspberry Pi Pico for the most speed per rupee and MicroPython.
| Arduino Uno R3 | ESP32 DevKit | Raspberry Pi Pico | |
|---|---|---|---|
| Logic level | 5 V | 3.3 V | 3.3 V |
| CPU | 8-bit, 16 MHz | Dual-core, 240 MHz | Dual-core, 133 MHz |
| RAM | 2 KB | 520 KB | 264 KB |
| Wireless | No | Wi-Fi + Bluetooth | Pico W only |
| Languages | Arduino C++ | Arduino C++, MicroPython, ESP-IDF | MicroPython, C/C++, Arduino |
| Best for | Learning, shields, 5 V modules | IoT, dashboards, home automation | Fast I/O, MicroPython, low cost |
- Logic level
- Arduino Uno R3:
- 5 V
- ESP32 DevKit:
- 3.3 V
- Raspberry Pi Pico:
- 3.3 V
- CPU
- Arduino Uno R3:
- 8-bit, 16 MHz
- ESP32 DevKit:
- Dual-core, 240 MHz
- Raspberry Pi Pico:
- Dual-core, 133 MHz
- RAM
- Arduino Uno R3:
- 2 KB
- ESP32 DevKit:
- 520 KB
- Raspberry Pi Pico:
- 264 KB
- Wireless
- Arduino Uno R3:
- No
- ESP32 DevKit:
- Wi-Fi + Bluetooth
- Raspberry Pi Pico:
- Pico W only
- Languages
- Arduino Uno R3:
- Arduino C++
- ESP32 DevKit:
- Arduino C++, MicroPython, ESP-IDF
- Raspberry Pi Pico:
- MicroPython, C/C++, Arduino
- Best for
- Arduino Uno R3:
- Learning, shields, 5 V modules
- ESP32 DevKit:
- IoT, dashboards, home automation
- Raspberry Pi Pico:
- Fast I/O, MicroPython, low cost
Try it: ADC resolution calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Drawing more than about 20 mA from a pin (8 mA on the R4). Use a transistor or driver module for motors, relays and buzzers.
- Connecting 12 V to the 5V pin instead of VIN or the barrel jack. This destroys the board.
- Leaving something wired to D0 or D1, which blocks uploads.
- Powering servos or motors from the Uno's 5 V pin, which causes resets and brown-outs.
- Forgetting a common ground between the Uno and an external power supply.
Frequently asked questions
Is the Arduino Uno good for beginners?
Yes. It is the most documented microcontroller board, it works with 5 V modules without level shifting, and the Arduino IDE hides most of the complexity of compiling and uploading.
Can the Arduino Uno connect to Wi-Fi?
The Uno R3 and R4 Minima cannot. The Uno R4 WiFi can, through its onboard ESP32-S3. Alternatively, use an ESP32 board on its own.
What voltage does the Arduino Uno need?
5 V over USB, or 7 to 12 V on the barrel jack or VIN pin for the R3. The R4 accepts 6 to 24 V on VIN.
Can I program an Arduino Uno with Python?
Not directly; the R3 is too small to run MicroPython. You can control it from Python on a PC over serial using the Firmata protocol, or choose a Raspberry Pi Pico or ESP32 if you want to write the board code in Python.
Are clone Uno boards safe to use?
Most work identically. The usual difference is a CH340 USB chip that needs a driver on some Windows versions. Buy from a seller who tests boards so you are not debugging a bad solder joint.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 403 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Arduino UNO R3 product reference manual (Arduino)
- Arduino UNO R4 Minima and R4 WiFi datasheets (Arduino)
- ATmega328P datasheet (Microchip)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



