LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsFlames give off a strong burst of near-infrared light. This alarm uses a tuned IR sensor to spot a candle or lighter flame from up to a metre away and sounds a buzzer and flashing LED, holding the alarm for a few seconds after the flame goes out.
Test only with a small candle, on a non-flammable surface, with an adult present.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
flame_fire_alarm.inoVerify & upload in Electrolark// Flame detector fire alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "flame-fire-alarm"
// ---- pins ----
const uint8_t FLAME_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
// ---- latest readings ----
bool flame = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 4000; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (flame) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "FIRE" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
flame = digitalRead(FLAME_PIN) == LOW;
evaluate();
Serial.print(F("Flame="));
Serial.print(flame ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Flame Sensor Module – LM393, Digital/Analog Output, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 8 steps.
No. This page has the complete, tested code (flame_fire_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹434 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Comparator outputs and sensitivity trimmers; Current-limiting resistors for LEDs.
Test only with a small candle, on a non-flammable surface, with an adult present.
Ideas that reuse this build: Add a relay to start a small 12 V water pump and Connect it to Wi-Fi. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
Walk into the room and it sounds the alarm: the classic first security build.
A magnet and a glass reed switch tell you whenever a door or drawer opens.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flame=no, status=OK Flame=no, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.