How-to · Beginner · 3 min read
How to Use a Breadboard
Layout, Rails and Wiring Tips
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A solderless breadboard lets you build circuits by pushing parts and wires into holes, with no soldering. Inside, each short row of five holes is connected, the centre gap separates the two halves so ICs can straddle it, and the long side rails carry power and ground. Some full-size boards split their rails in the middle, so check before relying on them.
Key specs at a glance
- Full size
- 830 tie points (63 rows, 2 x 2 power rails)
- Half size
- 400 tie points
- Connections
- Each row of 5 holes on either side of the centre gap is joined
- Hole pitch
- 2.54 mm (0.1 inch), fits DIP ICs and header pins
- Current
- Keep under about 1 A per contact
- Wire
- 22 AWG solid core or Dupont jumpers
How a breadboard is connected inside
in the main area, the five holes in each numbered row (a to e, and f to j) are joined by a metal clip. Parts in the same row are connected.
separates the left and right halves. DIP chips such as the 555 timer straddle it, so each pin gets its own row.
the long lines marked red (+) and blue (-) along each edge run the length of the board. On some 830-point boards they are broken halfway, shown by a gap in the red and blue lines. Bridge them with jumpers if needed.
Building your first breadboard circuit
- 1Connect your supply (or the board's 5V and GND) to the + and - rails on one side, then link both sides' rails with two jumpers.
- 2Place the main part (microcontroller, IC or module) across or near the centre gap.
- 3Put each component's leads in different rows unless you want them connected.
- 4Use short, colour-coded wires: red for +, black for ground, other colours for signals.
- 5Check the circuit against the diagram, row by row, before applying power.
Breadboard power supply modules
An MB102-style breadboard power module plugs into the rails and turns a 6.5 to 12 V adapter or USB into 5 V and 3.3 V, selectable per side with jumpers. It suits sensors and logic but uses small linear regulators, so keep the total under about 500 mA; motors and LED strips need their own supply.
What breadboards are not good for
- High current: thin clips heat up above about 1 A.
- High frequency and precise analog work: neighbouring rows add stray capacitance.
- Mains voltage: never.
- Permanent builds: move finished circuits to a perfboard or PCB and solder them.
- Thick component legs and stranded wire: they spread or fail to grip the clips.
Try it: Ohm's law calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Placing both legs of a component in the same row, which shorts it out.
- Assuming power rails run the full length on boards that split them in the middle.
- Pushing an ESP32 DevKit into a single breadboard; it covers all the holes on one side. Use two half-size boards side by side or a wider board.
- Forgetting to connect the rails on both sides of the board.
- Using stranded wire, which frays and makes intermittent contacts.
Frequently asked questions
Which holes on a breadboard are connected?
In the main area, each row of five holes on one side of the centre gap. Along the edges, each long power rail is connected along its length, sometimes with a break in the middle.
Why is there a gap in the middle of a breadboard?
So chips in DIP packages can sit across it, with each pin in its own row and the two sides kept separate.
Can a breadboard handle 12 V?
Yes, voltage is not the issue at low-voltage DC; current is. Keep currents under about 1 A and never use it for mains.
What wire should I use on a breadboard?
22 AWG solid-core wire or pre-cut jumper wire kits for neat layouts, and male-to-male Dupont jumpers for quick connections to modules.
Why is my breadboard circuit not working?
Check the most common faults first: rails not connected or split, a component in the wrong row, a missing common ground, and a loose wire. A multimeter's continuity mode finds broken contacts quickly.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1519 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Solderless breadboard specifications (BusBoard Prototype Systems / 3M)
- MB102 breadboard power supply module documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




