Component guide · Beginner · 3 min read
555 Timer IC

Pinout, Astable and Monostable Circuits
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
The 555 timer is an 8-pin IC that creates time delays and oscillations with just a resistor and capacitor. In astable mode it blinks continuously at f = 1.44 / ((R1 + 2 x R2) x C). In monostable mode, a trigger produces one pulse lasting t = 1.1 x R x C. The NE555 runs from 4.5 to 16 V and its output can drive up to 200 mA.
Key specs at a glance
- Supply
- NE555: 4.5 to 16 V; CMOS TLC555: 2 to 15 V
- Output current
- Up to 200 mA source or sink (NE555)
- Astable frequency
- f = 1.44 / ((R1 + 2R2) x C)
- Monostable time
- t = 1.1 x R x C
- Package
- DIP-8 (556 = two timers in DIP-14)
- Timing range
- Microseconds to many minutes
555 timer pinout
Pin 1 is next to the notch or dot, counting anticlockwise from the top.
| Pin | Name | Function |
|---|---|---|
| 1 | GND | Ground |
| 2 | TRIG | Starts timing when pulled below 1/3 VCC |
| 3 | OUT | Output |
| 4 | RESET | Pull low to reset; tie to VCC when unused |
| 5 | CTRL | Control voltage; add 10 nF to ground |
| 6 | THR | Ends timing when above 2/3 VCC |
| 7 | DIS | Discharges the timing capacitor |
| 8 | VCC | Supply |
- 1
- Name:
- GND
- Function:
- Ground
- 2
- Name:
- TRIG
- Function:
- Starts timing when pulled below 1/3 VCC
- 3
- Name:
- OUT
- Function:
- Output
- 4
- Name:
- RESET
- Function:
- Pull low to reset; tie to VCC when unused
- 5
- Name:
- CTRL
- Function:
- Control voltage; add 10 nF to ground
- 6
- Name:
- THR
- Function:
- Ends timing when above 2/3 VCC
- 7
- Name:
- DIS
- Function:
- Discharges the timing capacitor
- 8
- Name:
- VCC
- Function:
- Supply
Astable mode: an LED blinker
Connect R1 from VCC to pin 7, R2 from pin 7 to pins 6 and 2 (joined), and C from pins 6/2 to ground. Pin 4 to VCC, 10 nF from pin 5 to ground, and the LED with a 330 Ω resistor from pin 3 to ground.
f = 1.44 / ((R1 + 2 x R2) x C)
(R1 + R2) / (R1 + 2 x R2)
Worked example: R1 = 10 kΩ, R2 = 68 kΩ, C = 10 µF gives f = 1.44 / (146,000 x 0.00001) = about 1 Hz, with the LED on 53% of the time.
Monostable mode: a one-shot timer
Connect R from VCC to pins 6 and 7 (joined), C from pins 6/7 to ground, and a push button from pin 2 to ground with a 10 kΩ pull-up on pin 2. Pressing the button sends pin 3 high for:
t = 1.1 x R x C. With R = 100 kΩ and C = 100 µF, t = 1.1 x 100,000 x 0.0001 = 11 seconds, useful for a staircase light or a doorbell delay.
Ready-made astable values
| R1 | R2 | C | Approx. frequency | Use |
|---|---|---|---|---|
| 1 kΩ | 10 kΩ | 100 µF | 0.7 Hz | Slow blinker |
| 10 kΩ | 68 kΩ | 10 µF | 1 Hz | 1-second flasher |
| 1 kΩ | 10 kΩ | 10 nF | 6.9 kHz | Tone for a passive buzzer |
| 1 kΩ | 6.8 kΩ | 10 nF | 9.6 kHz | PWM for LED dimming |
- 1 kΩ
- R2:
- 10 kΩ
- C:
- 100 µF
- Approx. frequency:
- 0.7 Hz
- Use:
- Slow blinker
- 10 kΩ
- R2:
- 68 kΩ
- C:
- 10 µF
- Approx. frequency:
- 1 Hz
- Use:
- 1-second flasher
- 1 kΩ
- R2:
- 10 kΩ
- C:
- 10 nF
- Approx. frequency:
- 6.9 kHz
- Use:
- Tone for a passive buzzer
- 1 kΩ
- R2:
- 6.8 kΩ
- C:
- 10 nF
- Approx. frequency:
- 9.6 kHz
- Use:
- PWM for LED dimming
NE555 vs CMOS 555 (TLC555, ICM7555)
The bipolar NE555 is robust and drives 200 mA loads, but draws several milliamps itself and puts spikes on the supply when it switches. CMOS versions run from 2 V (so they work at 3.3 V), draw microamps, and allow larger timing resistors, but drive much less output current. Use CMOS for battery circuits and the NE555 for driving relays or buzzers directly.
Try it: 555 astable calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Leaving RESET (pin 4) floating, which makes the timer stop at random.
- Omitting the 10 nF capacitor on pin 5, which lets noise shift the timing.
- Using a leaky electrolytic for long delays; timing becomes inaccurate. Use larger resistors and a film capacitor where possible.
- Driving a relay coil without a flyback diode across it.
- Using an NE555 at 3.3 V; it needs at least 4.5 V. Choose a TLC555.
Frequently asked questions
What is a 555 timer used for?
Blinkers, tone generators, delay timers, debouncing buttons, PWM motor and LED dimmers, and pulse generators. It is one of the most-used ICs in hobby electronics.
How do I calculate 555 timer frequency?
In astable mode, f = 1.44 / ((R1 + 2 x R2) x C), with resistances in ohms and capacitance in farads.
Can a 555 timer run on 3.3 V?
The NE555 needs at least 4.5 V. CMOS versions such as the TLC555 and ICM7555 run from 2 V and work well at 3.3 V.
Why do people still use the 555 when microcontrollers exist?
It needs no programming, works at up to 16 V, drives loads directly, and is cheap and robust. It is ideal for teaching timing and for simple standalone circuits.
What is the difference between 555 and 556?
The 556 contains two independent 555 timers in one 14-pin package.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 13 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- NE555 / SA555 / SE555 precision timers datasheet (Texas Instruments)
- TLC555 LinCMOS timer datasheet (Texas Instruments)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



