Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsBuilt-in heater thermostats can drift by several degrees. This controller reads the water with a sealed probe and switches a low-voltage aquarium heater through the relay, holding the tank between 25 and 26 °C.
Use a low-voltage (12 V) aquarium heater, or have a qualified electrician wire a mains heater through a certified enclosure.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
aquarium_heater_controller.inoVerify & upload in Electrolark// Aquarium heater controller
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "aquarium-heater-controller"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t RELAY_PIN = 3;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 25; // °C target for tropical fish
const float HYSTERESIS = 1; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Probe "));
lcd.print(probeC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC < ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "Heating" : "Temp OK";
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS18B20 Waterproof Temperature Probe – 1m Cable, 5V Relay Module with Optocoupler (1 channel), LCD1602 16x2 Character LCD (blue, with I2C adapter), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (aquarium_heater_controller.ino). Install these libraries first: OneWire, DallasTemperature and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹588 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Character displays and I²C backpacks; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Watch it from your phone. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Enter the PIN and a 12 V solenoid bolt pulls back for five seconds.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=Temp OK Probe=26.0C, status=Temp OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.