LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe RC522 reads each card's unique ID. If it matches one of the allowed IDs in the sketch, a servo slides a latch open for four seconds. Unknown cards get three red flashes and their ID printed so you can add new ones.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
13.56 MHz RFID/NFC reader that reads the unique ID of cards and key fobs held near it.
Small hobby servo that turns to any angle from 0 to 180° on command.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
Follow the colours: red is power, dark grey is ground, blue is a signal.
rfid_door_lock.inoVerify & upload in Electrolark// RFID card door lock
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "rfid-door-lock"
#include <SPI.h>
#include <MFRC522.h>
#include <Servo.h>
// ---- pins ----
const uint8_t RFID_SS = 2;
const uint8_t RFID_RST = 4;
const uint8_t SERVO_PIN = 3;
const uint8_t LED_GREEN = 5;
const uint8_t LED_RED = 6;
MFRC522 rfid(RFID_SS, RFID_RST);
Servo servo;
// Add your own card UIDs here (printed in the Serial Monitor when you scan a card)
const byte ALLOWED[][4] = {
{0xDE, 0xAD, 0xBE, 0xEF},
{0x12, 0x34, 0x56, 0x78},
};
const int LOCKED_ANGLE = 0;
const int OPEN_ANGLE = 90;
const unsigned long OPEN_MS = 4000;
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
bool isAllowed(const byte* uid) {
for (unsigned int i = 0; i < sizeof(ALLOWED) / sizeof(ALLOWED[0]); i++) {
if (memcmp(uid, ALLOWED[i], 4) == 0) return true;
}
return false;
}
void printUid(const byte* uid, byte len) {
Serial.print(F("Card UID: {"));
for (byte i = 0; i < len; i++) {
Serial.print(F("0x"));
if (uid[i] < 0x10) Serial.print('0');
Serial.print(uid[i], HEX);
if (i < len - 1) Serial.print(F(", "));
}
Serial.println(F("}"));
}
void setup() {
Serial.begin(115200);
SPI.begin();
rfid.PCD_Init();
servo.attach(SERVO_PIN);
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
servo.write(LOCKED_ANGLE);
Serial.println(F("Scan a card..."));
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) return;
printUid(rfid.uid.uidByte, rfid.uid.size);
if (rfid.uid.size >= 4 && isAllowed(rfid.uid.uidByte)) {
Serial.println(F("Access granted"));
setGreenLed(true);
servo.write(OPEN_ANGLE);
delay(OPEN_MS);
servo.write(LOCKED_ANGLE);
setGreenLed(false);
} else {
Serial.println(F("Access denied"));
for (int i = 0; i < 3; i++) { setRedLed(true); delay(150); setRedLed(false); delay(150); }
}
rfid.PICC_HaltA();
rfid.PCD_StopCrypto1();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check it is on 3.3 V and the SPI wires (SCK, MOSI, MISO) are on the hardware SPI pins.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, RC522 RFID Reader / Writer SPI Module with Card & Tag, TowerPro SG90 9g Micro Servo (180°), 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (rfid_door_lock.ino). Install these libraries first: MFRC522 and Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹551 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; PWM pulses and servo control; RFID, UIDs and SPI.
Ideas that reuse this build: Keypad code lock and Fingerprint lock (coming in batch 2). They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Scan a card...
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.