Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsPWM switches the MOSFET on and off thousands of times a second; the longer it stays on in each cycle, the faster the motor spins. A knob sets that "duty cycle" from 0 to 100 %.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A 10 kΩ knob that works as a voltage divider, giving an analog value you can map to anything.
Logic-level MOSFET used as a fast electronic switch, so a PWM pin can control a motor's speed.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Motor + to battery +, motor − to MOSFET drain, MOSFET source to GND (shared with the Uno). Diode across the motor, stripe to +.
pwm_fan_speed_knob.inoVerify & upload in Electrolark// DC fan speed controller
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "pwm-fan-speed-knob"
// ---- pins ----
const uint8_t POT_PIN = A0;
const uint8_t MOTOR_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int potPct = 0;
void setup() {
Serial.begin(115200);
pinMode(MOTOR_PIN, OUTPUT);
}
void loop() {
int raw = analogRead(POT_PIN);
int duty = map(raw, 0, ADC_MAX, 0, 255);
if (duty < 20) duty = 0; // dead zone so "off" really is off
analogWrite(MOTOR_PIN, duty);
Serial.print(F("Speed ")); Serial.print(duty * 100 / 255); Serial.println(F(" %"));
delay(50);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The wiper is on an outer pin. Move the signal wire to the middle leg.
Gate and drain swapped, or the 10 kΩ gate pull-down is missing.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, 16mm Rotary Potentiometer 10kΩ (Linear), Power MOSFET (TO-220, IRLZ44N), Hobby DC Motor (130 size), Diodes (Pack of 10, 1N4007), Resistor Assortment Kit (30 Values), Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (pwm_fan_speed_knob.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹502 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
MOSFET switching and flyback diodes; Voltage dividers and analogRead().
Ideas that reuse this build: Automatic temperature fan. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Speed 49 % Speed 49 % Speed 49 % Speed 49 % Speed 49 % Speed 49 % Speed 49 % Speed 49 % Speed 49 %
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.