Automatic dustbin lid
Wave your hand and the lid lifts by itself, then closes after three seconds.
Shop by category
Shop all componentsA servo arm presses down on a standard pump bottle whenever the ultrasonic sensor sees a hand within 8 cm. The MG996R metal-gear servo has the torque to press stiff pumps reliably.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Sends a 40 kHz ultrasonic ping and times the echo to measure distance from 2 cm to about 4 m.
Small hobby servo that turns to any angle from 0 to 180° on command.
4×AA pack for the servo (MG996R needs more current than USB gives)
Follow the colours: red is power, dark grey is ground, blue is a signal.
Servo red wire to the 4×AA pack +, pack − to Uno GND. Do not power the MG996R from the Uno 5 V pin.
touchless_sanitizer_dispenser.inoVerify & upload in Electrolark// Touchless hand sanitiser dispenser
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "touchless-sanitizer-dispenser"
#include <Servo.h>
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 4;
const uint8_t SERVO_PIN = 3;
Servo servo;
// ---- latest readings ----
float distCm = 0;
const int TRIGGER_CM = 8; // hand closer than this triggers
const int REST_ANGLE = 10;
const int ACTIVE_ANGLE = 110;
const unsigned long HOLD_MS = 800;
unsigned long activatedAt = 0;
bool active = false;
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
servo.attach(SERVO_PIN);
servo.write(REST_ANGLE);
}
void loop() {
distCm = readDistanceCm();
if (distCm > 0 && distCm < TRIGGER_CM) {
if (!active) Serial.println(F("Dispense"));
active = true;
activatedAt = millis();
}
if (active && millis() - activatedAt > HOLD_MS) active = false;
servo.write(active ? ACTIVE_ANGLE : REST_ANGLE);
delay(80);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HC-SR04 Ultrasonic Range Finder Sensor Module, TowerPro MG996R Metal Gear Servo (180°), Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (touchless_sanitizer_dispenser.ino). Install this library first: Servo.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹823 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
PWM pulses and servo control; Time-of-flight measurement with sound.
Ideas that reuse this build: Automatic dustbin lid. They are listed under Take it further on this page.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Dial in an exact servo angle, 2° per click, shown on screen.
Rotates a product 15° at a time so you can shoot 360° photos.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.