Touchless hand sanitiser dispenser
Hold your hand under it and a metal-gear servo presses the pump for you.
Shop by category
Shop all componentsA rotary encoder never runs out of travel like a knob, and each click is a precise step. Turn it to move the servo 2° per click, press it to centre, and read the exact angle on the OLED with a bar graph.
Tick anything you already have and the total updates.
Small hobby servo that turns to any angle from 0 to 180° on command.
Follow the colours: red is power, dark grey is ground, blue is a signal.
encoder_servo_positioner.inoVerify & upload in Electrolark// Precision servo positioner
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "encoder-servo-positioner"
#include <Servo.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t ENC_CLK = 2;
const uint8_t ENC_DT = 4;
const uint8_t ENC_SW = 5;
const uint8_t SERVO_PIN = 3;
Servo servo;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
int angle = 90;
int lastClk = HIGH;
const int STEP_DEG = 2; // degrees per click
void drawAngle() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Servo position"));
oled.setTextSize(3);
oled.setCursor(0, 22);
oled.print(angle);
oled.print((char)247); // degree sign in the built-in font
oled.drawRect(0, 56, 128, 8, SSD1306_WHITE);
oled.fillRect(0, 56, map(angle, 0, 180, 0, 128), 8, SSD1306_WHITE);
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(ENC_CLK, INPUT_PULLUP);
pinMode(ENC_DT, INPUT_PULLUP);
pinMode(ENC_SW, INPUT_PULLUP);
servo.attach(SERVO_PIN);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
servo.write(angle);
}
void loop() {
int clk = digitalRead(ENC_CLK);
if (clk != lastClk && clk == LOW) {
angle += (digitalRead(ENC_DT) != clk) ? STEP_DEG : -STEP_DEG;
angle = constrain(angle, 0, 180);
servo.write(angle);
drawAngle();
}
lastClk = clk;
if (digitalRead(ENC_SW) == LOW) { // press to centre
angle = 90;
servo.write(angle);
drawAngle();
delay(250);
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn slower, or add 100 nF capacitors from CLK and DT to GND to debounce.
Power the servo from a separate 5 V supply and join the grounds; add a 470 µF capacitor across the servo supply.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), KY-040 Incremental Rotary Encoder Module, TowerPro SG90 9g Micro Servo (180°), 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (encoder_servo_positioner.ino). Install these libraries first: Servo, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹570 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; PWM pulses and servo control; Quadrature encoders.
Ideas that reuse this build: Knob version. They are listed under Take it further on this page.
Hold your hand under it and a metal-gear servo presses the pump for you.
Wave your hand and the lid lifts by itself, then closes after three seconds.
Your first motion project: turn the knob and the servo follows.
Rotates a product 15° at a time so you can shoot 360° photos.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.