Concept explainer · Beginner · 3 min read
Series and Parallel Circuits
Resistors, LEDs, Batteries and Capacitors
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
In a series circuit, parts are in one chain: the same current flows through all of them, voltages add, and resistances add (R = R1 + R2). In parallel, parts share the same two points: the same voltage is across all, currents add, and total resistance falls (1/R = 1/R1 + 1/R2). Batteries in series add voltage; in parallel they add capacity.
Key specs at a glance
- Series resistors
- R = R1 + R2 + ...
- Parallel resistors
- 1/R = 1/R1 + 1/R2 + ...; two equal resistors give half
- Series capacitors
- 1/C = 1/C1 + 1/C2 (capacitance falls)
- Parallel capacitors
- C = C1 + C2 (capacitance adds)
- Batteries in series
- Voltage adds, capacity (mAh) stays
- Batteries in parallel
- Capacity adds, voltage stays (match cells)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
The rules in one table
| Series | Parallel | |
|---|---|---|
| Current | Same through every part | Divides between branches |
| Voltage | Divides across parts | Same across every branch |
| Resistors | Add up | Total is less than the smallest |
| Capacitors | Total is less than the smallest | Add up |
| Inductors | Add up | Less than the smallest |
| Batteries / cells | Voltage adds | Capacity adds |
| If one part fails open | Whole chain stops | Other branches keep working |
- Current
- Series:
- Same through every part
- Parallel:
- Divides between branches
- Voltage
- Series:
- Divides across parts
- Parallel:
- Same across every branch
- Resistors
- Series:
- Add up
- Parallel:
- Total is less than the smallest
- Capacitors
- Series:
- Total is less than the smallest
- Parallel:
- Add up
- Inductors
- Series:
- Add up
- Parallel:
- Less than the smallest
- Batteries / cells
- Series:
- Voltage adds
- Parallel:
- Capacity adds
- If one part fails open
- Series:
- Whole chain stops
- Parallel:
- Other branches keep working
Resistor examples
- 220 Ω + 330 Ω in series = 550 Ω.
- 220 Ω and 330 Ω in parallel: 1/R = 1/220 + 1/330, so R = 132 Ω.
- Two 1 kΩ in parallel = 500 Ω at double the power rating. Handy when you lack a value: two 470 Ω in parallel is a 235 Ω, 1/2 W resistor.
Series resistors form a voltage divider: the voltage across each is proportional to its resistance.
LEDs: series or parallel?
Series is better. Three red LEDs (2 V each) on 12 V need one resistor: (12 - 6) / 0.015 = 400 Ω. All get the same current. The limit is supply voltage: you cannot put three 3 V white LEDs on 5 V.
Parallel LEDs each need their own resistor. Sharing one resistor lets the LED with the lowest forward voltage hog the current and the others stay dim. See LEDs.
Batteries: series for voltage, parallel for capacity
- Four 1.5 V AA cells in series = 6 V, same 2000 mAh.
- Two 3.7 V, 2600 mAh Li-ion cells in series (2S) = 7.4 V, 2600 mAh. In parallel (1S2P) = 3.7 V, 5200 mAh.
- Only parallel cells of the same type, age and charge state; a fresh cell dumps current into a tired one. Series lithium packs need a BMS to keep cells balanced.
Capacitors behave the opposite way
Two 100 µF capacitors in parallel give 200 µF; in series they give 50 µF but the voltage rating adds. For smoothing a supply, add capacitors in parallel. See capacitors.
Checking a circuit with a multimeter
Measure voltage across a part (parallel to it) with the circuit on. Measure current by breaking the circuit and inserting the meter in series. Measure resistance with the power off and the part isolated, otherwise parallel paths give a lower reading. See how to use a multimeter.
Try it: Series parallel resistors calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Sharing one resistor between parallel LEDs.
- Putting LEDs in series on a supply lower than their total forward voltage.
- Paralleling mismatched or unprotected lithium cells.
- Measuring a resistor in-circuit and getting a lower value because of parallel paths.
- Expecting a parallel circuit to stop when one branch opens; only that branch stops.
Frequently asked questions
What is the difference between series and parallel?
In series the parts are in one loop and share the same current; in parallel they are side by side and share the same voltage.
How do I calculate resistors in parallel?
Use 1/R = 1/R1 + 1/R2. For two resistors, R = (R1 x R2) / (R1 + R2). Two equal resistors give half the value.
Do batteries in series last longer?
No. Series adds voltage but keeps the same mAh. Parallel adds capacity, so it lasts longer at the same voltage.
Why are house lights wired in parallel?
So every lamp gets the full supply voltage and one failing lamp does not switch off the rest.
Can I connect LEDs in parallel without resistors?
No. Each LED needs its own series resistor, or a constant-current driver, otherwise current is uneven and LEDs burn out.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- Horowitz and Hill, The Art of Electronics, chapter 1
- Kirchhoff's circuit laws, standard physics references
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



