Component guide · Beginner · 3 min read
Hobby DC Motors (130, 180, FF-180, RF-300, DVD Loader)

Specs, Wiring and Projects
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Small hobby DC motors like the 130 and 180 size, FF-180, RF-300 and dual-shaft toy motors run on 1.5 to 9 V and spin at thousands of RPM. They are used in school projects, fans, toy cars and solar demonstrations. Drive them with a transistor, MOSFET or small motor driver; an Arduino pin cannot supply their current.
Key specs at a glance
- Voltage
- 1.5 to 6 V (130), up to 9 V (FF-180)
- Speed
- About 3,000 to 12,000 RPM
- Running current
- About 70 to 300 mA
- Stall current
- About 0.5 to 2 A
- Shaft
- 2 mm on most
- RF-300
- Low current, used with small solar cells
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hobby DC Motor (130 / 180 Size)₹48
Option 2FF-180 DC Trimmer Motor 1.5V-9V₹43
Option 3RF-300 3.7V Micro DC Motor (6000 RPM)₹34
Option 4Round Toy DC Motor Dual Shaft High RPM (3V-6V)₹26
Option 5DVD Loader Gear DC Motor 33 x 32mm₹55
What the Hobby 130 and 180 DC motor is
The 130 and 180 size hobby motors are small, cheap brushed DC motors found in toys, school kits and fans. They run on a couple of AA cells and spin fast with little torque.
The RF-300 needs very little current, so it runs from a small solar panel, a classic science demonstration. The DVD loader motor includes a small gear train for slow, strong motion.
Add a flyback diode when switching a motor with a transistor or MOSFET.
Hobby 130 and 180 DC motor pinout
The pins on the Hobby 130 and 180 DC motor and what each one does.
| Pin | Function |
|---|---|
| + | Motor lead |
| - | Motor lead |
- +
- Motor lead
- -
- Motor lead
Wiring the Hobby 130 and 180 DC motor
Connect the Hobby 130 and 180 DC motor like this.
| Hobby 130 and 180 DC motor pin | Uno + MOSFET module | Uno + TB6612FNG |
|---|---|---|
| Motor + | Battery + | Driver OUT1 |
| Motor - | MOSFET drain (diode across motor) | Driver OUT2 |
| Gate / IN | D9 via the module | TB6612 IN pins |
- Motor +
- Uno + MOSFET module:
- Battery +
- Uno + TB6612FNG:
- Driver OUT1
- Motor -
- Uno + MOSFET module:
- MOSFET drain (diode across motor)
- Uno + TB6612FNG:
- Driver OUT2
- Gate / IN
- Uno + MOSFET module:
- D9 via the module
- Uno + TB6612FNG:
- TB6612 IN pins
Example code
A minimal sketch to check the part works.
const int M = 9;
void setup() {}
void loop() {
for (int s = 60; s <= 255; s += 5) { analogWrite(M, s); delay(40); }
delay(1000);
analogWrite(M, 0);
delay(1000);
}Setup and tuning
switch them with an NPN transistor (2N2222, BC547 for the smallest), a logic-level MOSFET or a small H-bridge for both directions.
fit a 1N4007 or 1N5819 across the motor, band to the + side, when switching with a transistor or MOSFET.
solder a 100 nF capacitor across the terminals to reduce interference with sensors and radios.
2 AA cells (3 V) suit 130 motors; do not exceed about 6 V or the brushes wear fast.
for solar demos use the RF-300, which starts at very low current.
What you need
Shop this list7 of 9 found in our store · ₹375
Hobby DC Motor (130 / 180 Size): the part this guide coversHobby DC Motor (130 / 180 Size)₹48
FF-180 DC Trimmer Motor 1.5V-9V: another version this guide coversFF-180 DC Trimmer Motor 1.5V-9V₹43
RF-300 3.7V Micro DC Motor (6000 RPM): another version this guide coversRF-300 3.7V Micro DC Motor (6000 RPM)₹34
Round Toy DC Motor Dual Shaft High RPM (3V-6V): another version this guide coversRound Toy DC Motor Dual Shaft High RPM (3V-6V)₹26
DVD Loader Gear DC Motor 33 x 32mm: another version this guide coversDVD Loader Gear DC Motor 33 x 32mm₹55- Uno R3 development board: the controller used in the wiring tableFind this part
MOSFET switch module (D4184 / LR7843): to switch a motor on and off with PWMMOSFET Switch Module, Relay Replacement (D4184 / LR7843)₹39- 1N4007 diode: flyback protection across the motorFind this part
TB6612FNG dual motor driver: for small 3 to 12 V motorsTB6612FNG Dual Motor Driver Module₹130Closest match, check the specs
Alternatives and when to choose them
- TT and BO gear motors: geared for wheels.
- DC motors.
- Transistors and MOSFETs.
Common mistakes to avoid
- Driving the motor from a GPIO pin, which can damage the board.
- Switching it with a transistor but no flyback diode.
- Running a 3 V motor at 9 V, which burns out the brushes.
- Expecting torque from a motor with no gearbox.
Frequently asked questions
Can a small solar cell run a hobby motor?
Yes, the RF-300 is made for that: it starts with very little current, so a small 2 to 3 V solar cell spins it.
Can I run it straight from an Arduino pin?
No. Even a small motor draws 70 to 300 mA and more at start-up, far above a pin's limit. Use a transistor, MOSFET or motor driver.
How do I reverse the motor?
Swap the two wires, or use an H-bridge driver such as an L9110S or TB6612FNG to reverse it from code.
What voltage do hobby motors need?
Usually 3 to 6 V. The FF-180 tolerates up to about 9 V.
What is the DVD tray motor?
A small motor with its own gear train from a disc tray, giving slow, strong motion for light mechanisms.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


