Component guide · Beginner · 4 min read
DC Motors Explained

BO, N20 and Geared Motors for Robots
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A brushed DC motor spins when current flows through it: voltage sets the speed and the load sets the current it draws. A gearbox trades speed for torque, which is why robot motors such as BO and N20 motors are geared. Control speed with PWM and direction with an H-bridge motor driver, never straight from a microcontroller pin.
Key specs at a glance
- Key ratings
- Rated voltage, no-load RPM, rated torque, stall current
- BO motor
- 3 to 12 V (6 V typical), plastic gearbox, common in 2WD and 4WD robot kits
- N20 micro gear motor
- 3, 6 or 12 V versions, metal gears, many ratios, optional encoder
- Speed control
- PWM duty cycle via a motor driver
- Direction
- Reverse polarity, using an H-bridge
- Noise suppression
- 0.1 µF ceramic capacitor across the terminals
How a DC motor works
Inside a brushed DC motor, permanent magnets surround a coil on a shaft. Brushes feed current to the coil through a segmented commutator, which keeps flipping the current so the coil keeps turning. Reverse the supply and the motor reverses. Spinning also generates a voltage (back-EMF) that opposes the supply, which is why current is lowest at full speed and highest when the shaft is held still.
Reading a DC motor's ratings: RPM, torque and stall current
speed with nothing attached, at rated voltage.
the turning force it can deliver continuously, in kg·cm or N·m. 1 kg·cm lifts 1 kg on a 1 cm arm.
the current when the shaft is blocked. Every start, reverse and collision briefly approaches it, so size your [motor driver](#/guides/motor-drivers) and battery for stall current, not running current.
a 1:48 gearbox divides speed by 48 and multiplies torque by roughly 48, minus gearbox losses.
Common hobby DC motors compared
| Motor | Typical voltage | Typical use | Notes |
|---|---|---|---|
| BO motor (straight or L-shape) | 3 to 12 V | Beginner robot cars | Cheap, plastic gears, 100 to 300 RPM options |
| N20 micro metal gear motor | 3 to 12 V | Small robots, locks, line followers | Many ratios, encoder versions for speed feedback |
| 130 / 180 hobby motor | 1.5 to 6 V | Fans, toys, science kits | High RPM, low torque, no gearbox |
| Johnson / 25GA geared motor | 6 to 24 V | Heavier robots | Metal gearbox, higher torque |
| 775 / 795 motor | 12 to 24 V | Drills, grinders, mixers | Several amps running; needs a high-current driver |
- BO motor (straight or L-shape)
- Typical voltage:
- 3 to 12 V
- Typical use:
- Beginner robot cars
- Notes:
- Cheap, plastic gears, 100 to 300 RPM options
- N20 micro metal gear motor
- Typical voltage:
- 3 to 12 V
- Typical use:
- Small robots, locks, line followers
- Notes:
- Many ratios, encoder versions for speed feedback
- 130 / 180 hobby motor
- Typical voltage:
- 1.5 to 6 V
- Typical use:
- Fans, toys, science kits
- Notes:
- High RPM, low torque, no gearbox
- Johnson / 25GA geared motor
- Typical voltage:
- 6 to 24 V
- Typical use:
- Heavier robots
- Notes:
- Metal gearbox, higher torque
- 775 / 795 motor
- Typical voltage:
- 12 to 24 V
- Typical use:
- Drills, grinders, mixers
- Notes:
- Several amps running; needs a high-current driver
How to control speed and direction
A microcontroller pin supplies a few milliamps; even a small motor needs hundreds. Use:
a logic-level MOSFET on the low side plus a flyback diode across the motor, driven by PWM.
an H-bridge driver such as the TB6612FNG, L298N or DRV8833. See motor drivers.
add an encoder (N20 and 25GA versions) to measure real speed and distance.
How to choose a DC motor for a robot
- 1Estimate the robot's weight and wheel diameter.
- 2Pick a target speed. Wheel RPM = speed (m/min) / (pi x wheel diameter in m). For 30 m/min on 65 mm wheels, about 150 RPM.
- 3Check torque: a rough rule for flat floors is rated torque per motor of at least (robot weight in kg x wheel radius in cm) / number of driven wheels, with a 2x margin for slopes and starts.
- 4Match the voltage to your battery and confirm the driver handles the stall current.
Try it: Motor power torque calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Driving a motor directly from an Arduino or ESP32 pin.
- Sizing the driver for running current instead of stall current.
- Powering motors and the microcontroller from one weak battery; motor surges reset the board.
- Skipping noise capacitors; brush sparking can corrupt sensor readings and Wi-Fi.
- Choosing high RPM for a heavy robot; it will stall instead of moving.
Frequently asked questions
What is a BO motor?
A BO (battery operated) motor is a low-cost plastic-geared DC motor, usually run on 3 to 12 V, used in beginner robot car kits with matching wheels.
How do I control DC motor speed with Arduino?
Send a PWM signal with analogWrite() to the enable or PWM pin of a motor driver. The duty cycle sets the average voltage, and so the speed.
Can I run a 12 V DC motor at 6 V?
Yes, it will run slower and with less torque. Running far above its rated voltage shortens its life.
Why does my DC motor reset my Arduino?
Start-up current dips the supply voltage and brush noise travels along shared wires. Use a separate motor supply, common ground, a capacitor across the motor and a 470 to 1000 µF capacitor on the driver supply.
What is the difference between a DC motor and a stepper motor?
A DC motor spins continuously and needs feedback for exact positioning. A stepper motor moves in fixed steps, so it can position accurately without a sensor, but is heavier and less efficient.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 8 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
- Brushed DC motor fundamentals application note AN905 (Microchip)
- Pololu micro metal gearmotor specifications (Pololu)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



