Component guide · Beginner · 3 min read
MT3608 boost converter

Pinout, Wiring and Code
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The MT3608 module steps a low DC voltage up, for example 3.7 V from a Li-ion cell to 5 V or 12 V. Input is 2 to 24 V and output is adjustable up to 28 V with the trimmer. The switch is rated 2 A, so output current is much lower: about 0.5 to 1 A at 5 V from one cell.
Key specs at a glance
- Input
- 2 to 24 V
- Output
- Adjustable, up to 28 V (must be higher than input)
- Switch current
- 2 A (input side)
- Practical output
- About 0.5 to 1 A at 5 V from 3.7 V
- Efficiency
- Up to about 90 percent, lower at high step-up ratios
- Switching
- 1.2 MHz
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the MT3608 boost converter is
A boost converter stores energy in an inductor and releases it at a higher voltage. Power is conserved, so stepping 3.7 V up to 12 V means the input current is more than three times the output current. That is why output current falls quickly as the step-up ratio rises.
The MT3608 is a tiny, cheap module for powering 5 V boards from a single Li-ion cell, or a 12 V sensor from 5 V USB.
MT3608 boost converter pinout
The pins on the MT3608 boost converter and what each one does.
| Pin | Function |
|---|---|
| VIN+ / VIN− | Input 2 to 24 V |
| VOUT+ / VOUT− | Boosted output |
| Trimmer | Sets the output (often turned many times anticlockwise to raise it) |
- VIN+ / VIN−
- Input 2 to 24 V
- VOUT+ / VOUT−
- Boosted output
- Trimmer
- Sets the output (often turned many times anticlockwise to raise it)
Wiring the MT3608 boost converter
Set the output with no load first. The output can never be lower than the input, because a boost converter passes the input through its diode when off.
| MT3608 boost converter pin | Arduino Uno | ESP32 |
|---|---|---|
| VIN+ / VIN− | 18650 cell + / − | 18650 cell + / − |
| VOUT+ | 5V pin (set to 5.0 V) | 5V pin (set to 5.0 V) |
| VOUT− | GND | GND |
- VIN+ / VIN−
- Arduino Uno:
- 18650 cell + / −
- ESP32:
- 18650 cell + / −
- VOUT+
- Arduino Uno:
- 5V pin (set to 5.0 V)
- ESP32:
- 5V pin (set to 5.0 V)
- VOUT−
- Arduino Uno:
- GND
- ESP32:
- GND
Example code
Watching the cell voltage lets you stop before over-discharging a Li-ion cell; the MT3608 will keep drawing current until the cell is flat.
// divider 100k/100k from the cell to GPIO 34, 100k/33k from VOUT to GPIO 35
void setup() { Serial.begin(115200); analogReadResolution(12); }
void loop() {
float vbat = analogReadMilliVolts(34) * 2.0 / 1000.0;
float vout = analogReadMilliVolts(35) * (133.0 / 33.0) / 1000.0;
Serial.printf("Cell %.2f V Out %.2f V\n", vbat, vout);
delay(1000);
}Setup and tuning
the MT3608 has none. Use a protected cell or a BMS so the cell does not drop below about 3.0 V.
estimate with output power ÷ efficiency ÷ input voltage and keep the input current under about 1.5 A.
add a 100 µF capacitor on the output for sensitive sensors.
a TP4056 followed by an MT3608 makes a simple power bank for projects.
What you need
Shop this list5 of 5 found in our store · ₹4,47,582
MT3608 mini boost converter module: the converter this guide coversMT3608 Mini Boost Converter Module₹42
18650 battery holder: for a battery-powered buildBattery Holder₹45
TP4056 1A Li-ion charger module with protection: to charge the cellTP4056 1A Li-ion Charger Module with Protection₹19
Digital multimeter: to set and check output voltageDigital Multimeter₹177
ESP32-WROOM-32 38-pin development board: if you want Wi-Fi or Bluetooth controlESP32-WROOM-32 38-Pin Development Board₹389
Alternatives and when to choose them
- XL6009: larger boost module with more output current.
- LM2596: for stepping down.
- Lithium batteries: choosing cells and protection.
Try it: Boost converter design calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Expecting 2 A at the output; that is the internal switch rating.
- Setting the output lower than the input.
- Draining an unprotected Li-ion cell below 3 V.
- Turning the trimmer the wrong way and getting 28 V on a 5 V board.
Frequently asked questions
Can the MT3608 give 5 V 2 A from one 18650?
No. Expect about 0.5 to 1 A at 5 V. For more, use two cells in series with a buck converter, or a bigger boost module.
Why is the output equal to the input?
The trimmer is set below the input voltage. Turn it until the output rises.
Does it protect the battery?
No. Use a protected cell or a BMS board.
Can it make 12 V from USB 5 V?
Yes, at roughly 300 mA output, enough for a small 12 V sensor or fan.
Which way do I turn the trimmer?
On most modules anticlockwise raises the voltage, but check with a multimeter.
Is the output stable enough for sensors?
Usually yes; add a capacitor on the output for analog sensors.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

