How-to · Intermediate · 3 min read
BMS Boards for 2S, 3S and 4S Li-ion Packs
Wiring and Choosing
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A BMS (battery management system) board protects a multi-cell lithium pack: it cuts off on over-charge, over-discharge, short circuit or over-current, and many also balance the cells. Choose one for your cell count (2S, 3S, 4S) and chemistry, rated above your load current. Wire the balance taps in order from B- upwards, then charge with a CC/CV charger at the pack's full voltage.
Key specs at a glance
- Cell count
- Must match: 2S = 8.4 V, 3S = 12.6 V, 4S = 16.8 V full (Li-ion)
- Protection
- Over-charge (~4.25 V/cell), over-discharge (~2.5 to 3.0 V/cell), short, over-current
- Current rating
- Continuous amps; choose above your load with margin
- Balancing
- Passive bleed resistors on many boards; small current
- Pads
- B- (pack minus), B1, B2... (cell junctions), B+, P- (load and charger minus)
- Chemistry
- Li-ion/LiPo and LiFePO4 boards differ; do not mix
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What a BMS protects against
Lithium cells are damaged, and can catch fire, if charged above about 4.2 to 4.25 V or discharged too low. In a series pack, the charger only sees the total voltage, so one weak cell can be overcharged while the total looks fine. The BMS watches every cell through the balance wires and switches the pack off through MOSFETs on the negative side when a limit is crossed. It also trips on short circuit and excessive current. Balancing boards bleed a little energy from the highest cells near full charge so the cells stay matched.
Wiring a 3S BMS step by step
- 1Build the pack: three cells in series. Label the junctions.
- 2With nothing connected to the BMS, wire B- to the pack's most negative terminal.
- 3Wire B1 to the junction between cell 1 and cell 2, B2 to the junction between cell 2 and cell 3, and B+ (if present) to the pack's positive terminal.
- 4Check each cell voltage at the BMS pads with a multimeter.
- 5The load and charger connect between the pack's + and the BMS P- pad. The pack + goes straight to the load; only the negative passes through the BMS.
- 6Some boards need a brief charger connection to 'wake' after first assembly.
Connect balance wires in order from lowest to highest; connecting them out of order can damage the board.
Choosing the right board
| Use | Cells | Typical BMS rating |
|---|---|---|
| Small robot or LED project | 2S (7.4 V) | 3 to 5 A |
| 12 V projects, routers, CCTV backup | 3S (11.1 V) | 10 to 20 A |
| Robot cars with bigger motors, 14.8 V tools | 4S (14.8 V) | 20 to 40 A |
| LiFePO4 12.8 V pack | 4S LiFePO4 | Board made for LiFePO4 (3.65 V/cell) |
- Small robot or LED project
- Cells:
- 2S (7.4 V)
- Typical BMS rating:
- 3 to 5 A
- 12 V projects, routers, CCTV backup
- Cells:
- 3S (11.1 V)
- Typical BMS rating:
- 10 to 20 A
- Robot cars with bigger motors, 14.8 V tools
- Cells:
- 4S (14.8 V)
- Typical BMS rating:
- 20 to 40 A
- LiFePO4 12.8 V pack
- Cells:
- 4S LiFePO4
- Typical BMS rating:
- Board made for LiFePO4 (3.65 V/cell)
Charging a pack with a BMS
Use a charger set to the pack's full voltage (4.2 V x cells for Li-ion) with constant-current, constant-voltage (CC/CV) charging, for example a lab supply set to 12.6 V with a current limit, or a dedicated 3S charger. The BMS is a safety net, not a charger. Do not use a TP4056 on a series pack; it is for single cells only. Balancing currents on cheap boards are tiny (around 30 to 60 mA), so start with cells at matched voltages. See lithium batteries.
Try it: Battery pack calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Connecting balance wires out of order.
- Using a Li-ion BMS on LiFePO4 cells or vice versa.
- Choosing a BMS rated below the motor's stall current, so it trips on start.
- Charging a series pack with a single-cell TP4056.
- Building packs from mismatched or used cells.
Frequently asked questions
Do I need a BMS for a lithium battery pack?
Yes, for any multi-cell pack you build or charge yourself. It prevents over-charge, over-discharge, short circuits and over-current.
What is the difference between a BMS and a balance charger?
A BMS stays in the pack and protects it during charge and use. A balance charger only manages the cells while charging.
Why does my BMS cut off when the motor starts?
The inrush or stall current exceeds the BMS rating. Choose a higher-current BMS or reduce the inrush.
How do I wire a 3S BMS?
B- to pack minus, B1 and B2 to the cell junctions, B+ to pack plus, then load and charger between pack plus and P-.
What voltage do I charge a 3S pack to?
12.6 V for Li-ion or LiPo (4.2 V per cell) using a CC/CV charger. LiFePO4 3S charges to 10.95 V.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



