Solder a fused 12 V to 5 V power board on stripboard
Your first useful soldering project: a switched, fused board that turns 12 V into 5 V with its own voltmeter and plug-in outputs.
Shop by category
Shop all componentsA multimeter shows an average; an oscilloscope shows what a signal does over time. The DSO138 kit is a single-channel scope you solder yourself, good to about 200 kHz. Once it works, you measure three sources: PWM from an Arduino, a 555 astable oscillator on a breadboard, and the sine, square and triangle outputs of an XR2206 function generator kit.
Use only low-voltage signals under 30 V.
Let the soldering iron cool in its stand.
Tick anything you already have and the total updates.
Si5351 clock generator: square waves up to 160 MHz for radio projects
AD9833 programmable sine/triangle/square generator
Faster handheld scope when you outgrow the DSO138
Ready-built small scope with a 2.4 inch screen
Follow the colours: red is power, dark grey is ground, blue is a signal.
The DSO138 and XR2206 need a 9 V DC supply each (sold separately); the Uno runs from USB.
pwm_test.inoVerify & upload in Electrolark// Steps the PWM duty cycle so you can watch it on the scope
void setup() { Serial.begin(115200); }
void loop() {
int duty[] = {25, 64, 128, 191, 230};
for (int i = 0; i < 5; i++) {
analogWrite(9, duty[i]);
Serial.print("Duty "); Serial.print(duty[i] * 100 / 255); Serial.println(" %");
delay(4000);
}
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the trigger mode (AUTO) and that the probe ground clip is connected.
Set the trigger level to the middle of the signal and the slope to rising.
Check pin 4 is at 5 V; if it is low, the 555 stays reset.
No. Never connect a hobby oscilloscope to mains; you need isolated, rated equipment and training.
About 200 kHz analog bandwidth and up to 50 V input with the probe settings it supports.
Pin 9 uses Timer1 at that default frequency; pins 5 and 6 run at about 980 Hz.
14 parts: DSO138 Pocket Oscilloscope Kit, Oscilloscope Probe and Test Leads, XR2206 Function Generator DIY Kit, Uno R3 CH340G ATmega328p Compatible Development Board, NE555 Timer IC (DIP-8), Resistor Assortment Kit (30 Values), Electrolytic Capacitor by Value, Si5351 Clock Generator Module, 8 kHz to 160 MHz, I2C, AD9833 Programmable DDS Signal Generator Module, FNIRSI Oscilloscope (Handheld and Tablet), plus 4 more. Tools: Noel Soldering Iron, Solder Wire 60/40 Rosin Core and Digital Multimeter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 4 hours. The build on this page has 6 steps.
No. This page has the complete, tested code (pwm_test.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹10,454 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Timebase, volts per division and triggering; Reading frequency and duty cycle; How a 555 astable sets its frequency.
Ideas that reuse this build: Fused 12 V to 5 V power board. They are listed under Take it further on this page.
Your first useful soldering project: a switched, fused board that turns 12 V into 5 V with its own voltmeter and plug-in outputs.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Duty 9 %
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.