Buying guide · Beginner · 3 min read
The Starter Electronics Toolkit
What to Buy First
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Start with a breadboard, jumper wires and a digital multimeter, which cover most first projects with no soldering. Next add a temperature-controlled soldering iron, solder with flux, flush cutters, wire strippers, tweezers and safety glasses. A precision screwdriver set, caliper, crimping tool, bench power supply and oscilloscope come later as projects grow. Good basic tools last for years, so buy fewer, better ones.
Key specs at a glance
- Stage 1
- Breadboard, jumper wires, multimeter
- Stage 2
- Soldering iron, solder, flux, wick, cutters, strippers, tweezers
- Stage 3
- Screwdrivers, caliper, crimper, heat shrink, hot glue
- Stage 4
- Bench power supply, oscilloscope, hot air station
- Safety
- Glasses, ventilation or fume extractor, heat-proof mat
- Storage
- Compartment boxes for parts, labelled
The checklist
| Tool | Why you need it | Buying tip |
|---|---|---|
| Breadboard and jumpers | Build circuits without soldering | Full-size 830-point, with a mix of M-M and M-F leads |
| Digital multimeter | Check voltage, continuity and resistance | Auto-ranging with continuity beeper |
| Soldering iron | Headers, wires, permanent builds | Temperature-controlled, 60 W or more, with spare tips |
| Solder, flux, wick | Clean joints and fixing mistakes | 0.6 to 0.8 mm rosin-core; a flux pen |
| Flush cutters | Trim leads neatly | Small, sharp, for copper only |
| Wire strippers | Strip insulation without nicking copper | Gauge-marked or automatic |
| Tweezers | Place small parts | Fine-tip, anti-static |
| Helping hands or PCB holder | Hold boards while soldering | Weighted base |
| Precision screwdrivers | Terminal blocks and cases | Interchangeable bits |
| Caliper | Measure parts and connector pitch | Digital, 150 mm |
| Safety glasses | Leads fly when cut, solder splashes | Always on when cutting and soldering |
- Breadboard and jumpers
- Why you need it:
- Build circuits without soldering
- Buying tip:
- Full-size 830-point, with a mix of M-M and M-F leads
- Digital multimeter
- Why you need it:
- Check voltage, continuity and resistance
- Buying tip:
- Auto-ranging with continuity beeper
- Soldering iron
- Why you need it:
- Headers, wires, permanent builds
- Buying tip:
- Temperature-controlled, 60 W or more, with spare tips
- Solder, flux, wick
- Why you need it:
- Clean joints and fixing mistakes
- Buying tip:
- 0.6 to 0.8 mm rosin-core; a flux pen
- Flush cutters
- Why you need it:
- Trim leads neatly
- Buying tip:
- Small, sharp, for copper only
- Wire strippers
- Why you need it:
- Strip insulation without nicking copper
- Buying tip:
- Gauge-marked or automatic
- Tweezers
- Why you need it:
- Place small parts
- Buying tip:
- Fine-tip, anti-static
- Helping hands or PCB holder
- Why you need it:
- Hold boards while soldering
- Buying tip:
- Weighted base
- Precision screwdrivers
- Why you need it:
- Terminal blocks and cases
- Buying tip:
- Interchangeable bits
- Caliper
- Why you need it:
- Measure parts and connector pitch
- Buying tip:
- Digital, 150 mm
- Safety glasses
- Why you need it:
- Leads fly when cut, solder splashes
- Buying tip:
- Always on when cutting and soldering
What to buy when
First project (Arduino on a breadboard): breadboard, jumpers, multimeter. See the breadboard guide and multimeter guide.
First soldering: iron, solder, flux, wick, cutters, glasses and good ventilation. The soldering guide walks through your first joints.
Wiring robots and power: wire strippers, crimping tool, heat shrink, thicker wire.
Debugging bigger builds: a bench power supply with current limit, then an oscilloscope.
Workspace safety
Solder in a ventilated room or use a fume extractor, as flux smoke irritates the lungs. Wash your hands after handling leaded solder and before eating. Keep the iron in its stand, and work on a heat-proof silicone mat. Keep a small fire extinguisher suitable for electrical fires nearby when working with lithium batteries, and never leave charging cells unattended.
Common mistakes to avoid
- Buying a cheap fixed-temperature iron that oxidises tips.
- Using flush cutters on steel wire and chipping them.
- Skipping safety glasses.
- Buying a large cheap kit full of tools you never use.
- Soldering without ventilation.
Frequently asked questions
What tools do I need to start Arduino?
A breadboard, jumper wires and a multimeter. Soldering tools can wait until you need permanent builds or to solder headers.
What soldering iron should a beginner buy?
A temperature-controlled iron of 60 W or more with replaceable tips; set it around 330 to 350 °C for leaded solder.
Do I need an oscilloscope as a beginner?
No. A multimeter covers early projects. Add a scope when you start debugging PWM, serial data or power supply noise.
Leaded or lead-free solder?
Leaded (63/37) is easier to learn with; lead-free needs a hotter iron. Either way, ventilate and wash your hands.
What else is useful but often forgotten?
Heat shrink tubing, a flux pen, labelled parts boxes and a silicone work mat.
Parts for this guide
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.





