Component guide · Beginner · 3 min read
Jumper Wires and Dupont Connectors
Types, Crimping and Tips
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Jumper wires are short leads with pins or sockets that plug into breadboards and 2.54 mm headers. Male-to-male wires join breadboard points, male-to-female wires join a breadboard to a module's header pins, and female-to-female wires join two boards' pins directly, such as a sensor to a Raspberry Pi. The plastic ends are Dupont-style housings; you can crimp your own for tidy, exact-length cables.
Key specs at a glance
- Pitch
- 2.54 mm (0.1 inch)
- Types
- Male-male, male-female, female-female; solid-core breadboard jumpers
- Wire
- Usually 26 to 28 AWG stranded
- Current
- Keep under about 1 A per lead; less for long, thin wires
- Lengths
- 10, 20 and 30 cm common
- Crimp housings
- 1 to 10 pin single row, also 2-row
Which jumper do you need?
| Type | Ends | Use it for |
|---|---|---|
| Male to male | Pin to pin | Breadboard to breadboard, Arduino header to breadboard |
| Male to female | Pin to socket | Module header pins (sensors, OLED) to a breadboard or Arduino |
| Female to female | Socket to socket | Module to Raspberry Pi GPIO or module to module |
| Solid-core pre-formed jumpers | Bent bare wire | Neat, flat breadboard wiring that stays put |
| Ribbon / rainbow cable | Multi-way | Pi GPIO extensions and tidy multi-pin links |
- Male to male
- Ends:
- Pin to pin
- Use it for:
- Breadboard to breadboard, Arduino header to breadboard
- Male to female
- Ends:
- Pin to socket
- Use it for:
- Module header pins (sensors, OLED) to a breadboard or Arduino
- Female to female
- Ends:
- Socket to socket
- Use it for:
- Module to Raspberry Pi GPIO or module to module
- Solid-core pre-formed jumpers
- Ends:
- Bent bare wire
- Use it for:
- Neat, flat breadboard wiring that stays put
- Ribbon / rainbow cable
- Ends:
- Multi-way
- Use it for:
- Pi GPIO extensions and tidy multi-pin links
Crimping your own Dupont leads
- 1Strip 2 to 3 mm of insulation from 24 to 28 AWG wire.
- 2Place the crimp pin in a ratcheting Dupont crimp tool (the jaw size for the wire, then the one for the insulation).
- 3Crimp once so the small tabs grip the bare wire and the larger tabs grip the insulation.
- 4Push the pin into the housing until the latch clicks; the small window tab faces up.
- 5Tug gently to check it is locked.
Ordinary pliers make weak crimps that fail later, so a proper ratcheting tool pays for itself quickly. JST-XH, JST-PH and Dupont pins look similar but are not interchangeable; see the connectors guide.
Loose contacts and other problems
Cheap jumpers are the most common cause of 'it worked yesterday' faults. Test suspect wires with a multimeter continuity check, replace any that feel loose in a header, and keep a few spares. Thin jumpers drop voltage at higher currents: a 30 cm 28 AWG lead carrying 1 A can lose around 0.1 V each way, enough to brown out a motor or LED strip. For power, use thicker wire or screw terminals. Colour-code your wiring (red for +, black for ground) to make debugging easier.
Try it: Voltage drop calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Running motors or LED strips through thin jumpers.
- Using pliers instead of a crimp tool.
- Mixing up JST and Dupont housings.
- Ignoring a wire that only works when wiggled.
- Using random colours so power and ground are hard to trace.
Frequently asked questions
What is the difference between male and female jumper wires?
A male end has a pin that plugs into a breadboard or socket; a female end has a socket that slides onto a header pin.
Which jumper wires do I need for a Raspberry Pi?
Female-to-female to connect a module's header pins directly to the GPIO header, or female-to-male to go from the GPIO to a breadboard.
How much current can a jumper wire carry?
Keep it under about 1 A for typical 26 to 28 AWG jumpers, and less over long lengths. Use thicker wire for motors and LED strips.
What is a Dupont connector?
The common 2.54 mm pitch plastic housing and crimp pin used on jumper wires and module headers.
Why does my circuit work only when I move the wires?
A loose or broken jumper. Check continuity with a multimeter and replace it.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




